Security: Intrusion

A BROKEN Green Circle could mean the following: Points are faulted and you can turn the system on to bypass those faulted points. Chime points are faulted and you would be hearing a Chime Tone. Both  conditions are occuring.

How to interpret a BROKEN Amber Circle on the EZ Series panel keypad.

How to enable/disabling encoding tones on the D1254 Keypad used wth the D7112.

How to disarm selected areas from a keypad with scope in multiple areas.

How to disarm All areas authorized by the user at once.

How to correct the inability to view troubles by pressing the 4-key on 2000 series panels.

  How to perform Zone Test from a Master Keypad on the DS7400 Series. DS7400,DS7400X,DS7400Xi,DS7400Xi (Ver 3+),DS7400Xi (Ver 4+)  

How to determine how many command centers (keypads) are supported by the D7112. How many command centers can be supported on the D7112?

How to Troubleshoot the D4412/D6412 keypad says Not Programmed, See Install Guide.

  How to checking system troubles on D6412 & D4412 using a D623 or D625 keypad.

   How to delete passcodes from the D4412 or D6412 using the D625 or D623 keypd. D623,D625,D6412,D4412.  

1.  Ensure the area is disarmed. 2.  Press Cmd + 4 + 2.  The flashing Cmd light is a prompt to enter a valid passcode.  3.  Enter a valid passcode and the D621 displays system trouble events by lighting the point indicators (zone leds)as described below:  Zone 1 Lit steady = Telephone line Fail  Zone 1 Slow Flash = Comm Fail, Destination 1  Zone 1 Fast Flash = Comm Fail, Destination 2  Zone 2 Lit steady = Alternate Comm Trouble  Zone 3 Lit steady = Installer Switch Closed  Zone 4 Lit steady = Backup Battery low  Zone 4 Lit steady = Slow Flash = Backup Battery Missing  Zone 5 Lit steady = Bell Supervision Fail  Zone 6 Lit steady = RF Receiver Jamming  Zone 6 Slow Flash = RF Receiver Trouble  Zone 7 Lit steady = Data Bus Device Missing  Zone 7 Slow Flash = Data Bus Device Tamper  Zone 7 Fast Flash = Data Buss Device Trouble/Reset  Zone 8 Lit steady = System Fault  Zone 8 Slow Flash = Service Interval  Zone 8 Fast Flash = Ground Fault Condition Press Cmd to return to the off state.

  How to View and clear Alarm Memory in the D6412 & D4412. D4412,D6412,D625,D623.  

How to 'Quick Arm' the DS7400XI Ver. 3+ control panel by pressing [#]+[ON] to arm.

How to interpret the two alternating asterisks (*) on the D8112 command center. D8112G2,D8112E1,D8112G1,D8112A

How to correct the correctly programmed D1260 displays 'CALL FOR SERVICE'. The D1260 displays CALL FOR SERVICE even though it is programmed correctly.  

How to locate the various connections and controls on the D636A keypad.

The keypad will display ‘Command Disabled’ when the Menu key is pressed for one of the following reasons. If the menu item # 1 in the function list is set with a function 0 and marked yes for any Command Center. If all of the Functions for the Command Center are selected as No (disabled). To prevent the keypad from displaying ‘Command Disabled’ after selecting Menu; Select a non-zero value for the Function # of Menu Item 1. Ensure that at least one of the Menu Items intended for use are set as Yes.

How to troubleshoot the 2000 series panel when the keypad reads Call For Service. My D2212 reads "Call For Service" and does not show anything else.  How do I determine the issue? D2212, D2412, D2812