Security: Intrusion

Bosch Building Technologies

Top Results

See all results

512 Views

0 Comments

Use the Menu function ‘MASER ARM’ to arm either selected areas or all areas that the user has authority in, which are in the scope of the keypad. Previously armed areas remain armed while the remaining disarmed will arm. For example, if a panel uses areas 1-8 and: The keypad has Panel Wide Scope and the user has authority only in areas 1, 2, 3 & 4, then only areas 1, 2, 3 & 4 will Master Arm. If the keypad has Custom Scope in areas 1 & 2 user has authority in areas 1, 2, 3 & 4, then only areas 1 & 2 will arm. Use the Menu function ‘MASER ARM’: Access the keypad Menus from the keypad. Press the NEXT key until the MASTER ARM ? function is displayed and select [ENTER]. Enter a valid passcode and press [ENTER]. The display shows MASTER ARM ALL ?, select [ENTER]. The command center displays ARMING X,X,X,X… where X= the available and authorized areas to arm.

1282 Views

0 Comments

524 Views

0 Comments

AC Fail/Res Rpt Default: No Selections: Yes/No Parameter Description: AC Power Supervision reports are sent to the central station and local printer at the time programmed for AC Fail Time. IMPORTANT: To comply with NFPA standards and UL 864 requirements for Commercial Fire Systems, program this item NO and program AC Tag Along as YES. Parameter Options Yes: Send AC Fail and AC Restoral reports. No: Do not send AC Fail and AC Restoral reports. Programming Instructions D5200 Programming 1) Receive copy of 9000MAIN 2) Enter group PANEL WIDE PARAMETER 3) Enter group Power Supervision 4) Fail/Res Rpt Yes/No (SPACE bar to change) *Must press ENTER for each prompt entry 5) Send Load to panel

760 Views

0 Comments

478 Views

0 Comments

635 Views

0 Comments

689 Views

0 Comments

678 Views

0 Comments

515 Views

0 Comments

655 Views

0 Comments

2576 Views

0 Comments

885 Views

0 Comments

423 Views

0 Comments

433 Views

0 Comments

411 Views

0 Comments

768 Views

0 Comments

1078 Views

0 Comments

810 Views

0 Comments

446 Views

0 Comments

443 Views

0 Comments

Top Contributors

1

David
New Poster
2

CPrince
New Poster
3

Anonymous
Not applicable
4

rlarkins
New Poster
5

Central_Support
Regular Contributor
6

Navyvet97
New Poster
7

Sabrina
New Poster
8

KenJ
New Poster
9

Anonymous
Not applicable
10

Anonymous
Not applicable

Bosch Building Technologies

Security: Intrusion

How to enable/disabling encoding tones on the D1254 Keypad used wth the D7112.

How to arm multiple areas with the Master Arm All command.

How to disarm All areas authorized by the user at once.

How to program the panels for AC fail report and AC restoral reports

How to disarm selected areas from a keypad with scope in multiple areas.

How to set the AC fail time on the 7000/9000 series panels

How to determine if the B key has been activated for a panic alarm

How to correct the inability to view troubles by pressing the 4-key on 2000 series panels.

How to perform Zone Test from a Master Keypad on the DS7400 Series.

How to determin the distance the FA400 can be mounted from the D8125INV

How to adjust the sensitivity on the DS937 Motion Detector.

How to troubleshoot missing D8125 Mux devices.

How to determine the number of passcodes are available in the D7112.

How to determine how many command centers (keypads) are supported by the D7112.

How to determine the capacity of the D7112 panel event log.

How to program a zone to activate Alternate Alarm.

How to Troubleshoot the D4412/D6412 keypad says Not Programmed, See Install Guide.

How to correct the Duplicate Point display when adding points into RF programming.

How to correct Bypass Reports Logging and/or Printing but not reporting to Central Station.

How to correct the 2000 series does not allow passcode changes by pressing the 5 key.

Security: Intrusion

Still looking for something?