Security: Intrusion

Part numbers D2212, D2212B, D2212BE, D2412, D2812, D223, D223A, D222, D222A, D220, D220A, D202, D202A

Issue When programming the phone number in a D4412/D6412 panel, how would a pause be entered in through keypad programming?   Solution   When a 4 second pause is needed while programming through the keypad, enter in a 13 for the nibble where you would like the pause to occur.

How to View Point Status on the DS7240/DS7220 panels. DS7220,DS7240,DS7447I

Issue How can a REX sensor such as the DS150i or DS160 be used to shunt an armed point? Solution  The REX sensor can be used to shunt a normally closed contact by connecting the REX relay contacts that will provide closure when motion is detected in parallel with the door point to be shunted. When these contacts close, a short will be placed across the door point. The panel will see the door as closed for the duration of the REX relay time. Note: The REX relay Common to Normally Open and Common to Normally Closed contacts will reverse when changing from Fail Safe to Fail Secure mode. See NOTES for further clarification. Notes DS150i: In Fail Safe mode, use the Yellow and Violet wires on the first relay or the Gray and Green wires on the second relay. In Fail Secure mode, use the Yellow and Blue wires on the first relay or the Gray and Orange wires on the e second relay. DS160: In Fail Safe mode, use the relay contacts designated Normally Open to Common. In Fail Secure mode, use the relay contacts designated Normally Closed to Common.

Overview Device Comm Error displays on the keypad.  Reports trouble zone 2. Wiring issue with the devices. Issue Device Comm Error displays on the D636 keypad. CS is receiving a Trouble zone 2 signal.   Solution   The devices (D636, D620, D640) have a wiring issue. All device data wiring should be connected in series. Example:  Data wire out from panel terminal 11 to the first device

Issue What are the SDI addresses on the D6412 and D4412?   Solution   SDI Address             Device Description 0 =           Installer Keypad, or local connection to RAM IV                         1-8 =          Command Center 1 to 8 40,41 =       DX8010 Telephone Control Module 50,51 =       RF Receivers 1, and 2 52-55 =      RF Keypads on RF Receiver 1 60-63 =       RF Keypads on RF Receiver 2 101-107 =   DX 2010 wired point expander 150-151 =   DX 3010 Octo-Output expander 250 =           DX4010 Serial RS-232 Interface module

How to force the DS7240/DS7220 to answer remote programming software. DS7240,DS7220,DS7445I,DS7447I

D6412, D4412

How to change user name text using a D1260 keypad. Can the user name text be changed from the keypad on a 7000/9000 or G-series panel?

Part number D2212, D2212B, D2212BE, D2412, D2812

How to  renew One Time Passcodes on 2000 series panels. D2212,D2412,D2812,D222A LCD,D223A LCD,D202A,D220A,D222,D223  

 Can the D125B be Used to Power 2 Wire Smokes on the D7112? Yes, see technogram number (73-06116-000-C) 1993 (attached). Listings and Approvals Underwriters Laboratories lists the D7112 ControVCommunicator as a Digital Alarm Communicator Transmitter (DACT) for: NFPA 71 Central Station, NFPA 72 Chapter 6 Local, NFPA 72 Chapter 8 Remote Station, NFPA 74 Household Fire Warning. The D7112 also has the following Approvals: CSFM and NYC-MEA (formerly NYC-BSA).

How to work with T-tapping POPIT Loops. D9127U,D8127T,D8125

How to properly use T-tapping with MUX devices with the D8125MUX. Is T-tapping acceptable when using MUX devices on the D8125MUX?