Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 
    Sort by:
    ‎01-19-2024 01:17 PM
    The following steps describe an efficient way to update the panel firmware in an AVENAR panel 4.x network via SD card, thus keeping downtime of the panels to a minimum. To further reduce downtime, it is recommended to network the panel nodes via ETH.
    View full article
    ‎10-31-2023 09:36 AM
    This article provides instructions for troubleshooting Ground Fault in the FPD-7024 or D7024
    View full article
    ‎05-02-2023 10:43 AM
    This article describes how to capture the panel/ controller communication log when requested by Technical support.
    View full article
    ‎05-02-2023 10:08 AM
    Panel controller displays can become de-calibrated, e.g. upon initial power-up followed by unintentional contact with the display or inaccurately touching the crosshairs.  It becomes noticeable after the panel controller has re-booted and does not respond properly to touch.
    View full article
    ‎11-11-2022 11:59 AM
    This article is a step by step guide about how to create panel container on map by using Macro-Area (point) on FMS.
    View full article
    ‎04-14-2022 05:08 PM
    This article explains how you can reset the FPA-1000, FPA-1000-UL, and FPA-1000-V2 panels.
    View full article
    ‎10-19-2022 03:52 PM
    This article explains step by step how to enable commands for operator (other than admin) in FSM
    View full article
    ‎10-18-2022 04:16 PM
    Have a look at this article and see how you can setup the FMS - OSD Logo
    View full article
    ‎10-18-2022 04:05 PM
    Follow this article and learn about the option which allows you to configure the color for each state & sensor in FSM
    View full article
    ‎10-18-2022 03:52 PM
    Library is offering 3 different sizes of detectors and can be customized. See this article and find out how you can customize Symbols (icons) - FSM
    View full article
    ‎10-18-2022 03:26 PM
    Live time event printing is supported. To enable it, add a xml file in program data folder with the name of the printer.
    View full article
    ‎10-18-2022 03:41 PM
    To silence all NAC's of one panel (FPA-5000/Avenar) from the map in FSM Step-by-step guide   Insert a sensor on the map of FSM Under sensor properties choose: General: Add symbol: FIRE_Panel_FPA_BG Settings: Driver Instance: the panel / compound where the FSM is belongs to Address-> e.g. Panel 1-10.1 ! Please pay attention: there are other “Panel” possibilities to choose. Please do not choose Panel 1-10 (Communication)! After inserting the settings click “ok” Then Apply At the map when you right click the panel symbol you will get the commands as shown below.   If there is a fire alarm, you can right click at the panel and then click at “silence on”. Please be sure, that then every NAC which is belonging to this panel is “silenced”. Additional: there is also a command "silence scope" which then has the effect, that the whole scope will be silenced.
    View full article
    ‎10-18-2022 03:46 PM
    This article presents step by step how to configure the “E-Mail Sender” function in FSM.
    View full article
    ‎10-18-2022 02:47 PM
    This article explain what should be done if new detectors are added to the system. 
    View full article
    ‎10-20-2022 01:58 PM
    This article explain how it is possible to automatically zoom in the map in case of alarm.
    View full article
    ‎09-07-2022 05:00 PM
    Follow this step-by-step guide and learn how you can use keypad programming to configure FPD-7024 IP communications
    View full article
    ‎08-04-2022 02:58 PM
    This article contains a step-by-step guide about how you can set the field of view (FoV) of AVIOTEC IP starlight 8000
    View full article
    ‎07-07-2022 04:07 PM
    Follow the steps from this article to see the labels from the sensors in FSM which are configured in RPS
    View full article
    ‎07-07-2022 04:02 PM
    Follow this step-by-step guide from this article and find out how to stop and restart the FSM Server service
    View full article
    ‎07-07-2022 03:38 PM
    Is always recommended to backup the database before running the default process. Find out in this article the steps to restore default FSM (Fire Monitoring System) configuration
    View full article
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist