Fire

Part numbers DS240, DS241, D296, D297

Uses for the  D298M over a D298S or D278S popited base? D278S 12 volt popit base. D298S 24 volt popit base. The D298M is a 24 volt popit base that provides connections for up to 19 supervised circuits two-wire slave detectors (D287 2-Wire Base with D285 Smoke Head or D285TH Smoke Head with 135 degree heat sensor) reporting to the master address. The D298M is used over the D298S to conserve popit addresses on a large system.

Issue Can the points, outputs and dialer be enabled and disabled from RPS? Solution No, This can only be done from the panel or a keypad attached to the panel. If any of the hard wire points are disabled then follow the steps below to enable points 1-8. Mux points 9 - 255 can be enabled using the "all" command if points 1 - 8 are enabled individually first. To Enable Points Press the Disable Button on the keypad. Press 2 Enable Press 1 Inputs Press 2 Individual Enter the point # (001 - 255) follow by # Repeat steps 3 – 5 until Points 1 -8 are enabled Press 1 Inputs Press 1 All Press the * Clear Button 4 times Follow the steps as above to enable Dialer - NAC's and Relays.

Part numbers FPC-500, FPC-500-P, FPC-500-C, FPC-500-C-P

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G

With FSM 5.6  the database.xml structure was slightly changed and FSM 5.6 is supporting only the new database.xml structure. This is leading after upgrade to a loss of the configured symbols (only the symbols, not the content of the devices configured on the floor plans). Therefore after upgrading from older FSM version (e.g. 5.2) to 5.6, the already configured symbols of sensors on maps are not shown correctly, they are shown are dots/circles.   Please note: If before executing the file provided below the application was opened and the sensor properties were edited by approving > at that step the symbols changed to the default symbol and the previously configured symbol cannot be recovered.

Part numbers D7052, D7024, FPD-7024, DS9400, DS9400I, DS9400M, MX363

Part Numbers FPA-1000, FPA-1000-UL, FPA-1000-V2, D10024A, D10024, D9024, D8024, D328, D328A, D327, D327A, FLM-325-N4, FLM-325-2R4, FLM-3252R4-A2, FLM-325-R24-A8

Issue One of the zones at the panel is in constant trouble.   Solution   Need to have proper wiring connections.  Check the following: 1. Using 12 Volt Smokes, Terminal 1 goes to Terminal 8 on the panel Switched AUX Power. 2. Make sure D136 relay is installed for Relay C for non G-Series panels. 3. For 24 Volt Smokes, Terminal 1 goes to a D130, and a UL 24 Volt PSU is needed on Terminal 8 on the Panel. Switched AUX Power goes to the D130 to reset the 24 Volt power. 4. Measure the EOL across loop "A" Terminals 7 and 9 of the D125B card. Look for 1.8K Ohms for the D125B on a new install or when adding to an existing install. If replacing a D125 or D125A the EOL would be 1.5K Ohms. 5. Measure the EOL across loop "B" Terminals 6 and 8 of the D125B card. Look for 1.8K Ohms on the D125B card on a new install or when adding to an existing install. If  replacing a D125 or D125A the EOL would be 1.5K Ohms. 6. Measure the Voltage across  Loop "A" Terminal 3 and Terminal 4 on the D125B card. The meter should read 2.5VDC with everything connected. If the reading is 5VDC the loop is Open (not seeing the 1.8K EOL across the last Smoke. If the voltage reading is Less than 1VDC you have a Short on the loop. The short could be a smoke head latched in alarm, bad/dirty smoke head, wiring short, or reversed polarity to one of the smoke heads on the loop. 7. Measure the Voltage across  Loop "B" Terminal 2 and Terminal 4 on the D125B card. The meter should read 2.5VDC with everything connected. If the reading is 5VDC the loop is Open (not seeing the 1.8K EOL across the last Smoke. If the voltage reading is Less than 1VDC you have a Short on the loop. The short could be a smoke head latched in alarm, bad/dirty smoke head, wiring short, or reversed polarity to one of the smoke heads on the loop. To verify the D125B is working correct you can wire the 1.8K Ohm EOL accross termainals 7 & 9 and another 1.8K Ohm EOL accross termainals 6 & 8. The Loop termainals 2 & 3 need to wire to the Positive Side of a 1K Ohm Zone. The EOL for the 1K Ohm zone is built in to the D125B. Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B9512G, B8512G, D125B

Part numbers D7024, DS9400, DS9400I, DS9400M

This article describes how to capture the panel/ controller communication log when requested by Technical support.

Part numbers D8125MUX, D7050, D7050TH, D5060, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G,

  Issue The D192G panel zone (point) is in trouble and the yellow LED is not on. Solution With the zone/point in trouble and No Yellow LED On there is a wiring fault. One of the following terminals do not have power connected to them. External Power In (EXT PWR IN) and / or Auxiliary Power In (AUX PWR IN). Terminal 1 (AUX PWR IN) 13.75 VDC Terminal 2 (Common) Terminal 3 (Supervised Zone / Point) 2.50 VDC Normal Condition < 1.50 VDC In Trouble condition Terminal 4 (Trigger) 13.75 VDC In Alarm Only Terminal 5 (External Power In) 12 VDC or 24 VDC Depended on needed Output for the NAC's or Power Supply Terminal 6 (Common) This is the Common from an 24 VDC External Power Terminal 7 (Positive Alarm Output) Terminal 8 (Negative Alarm Output) Part number D192G

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, D7034, FPE-7034, DS9434

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G,

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, D9127, D9127T, D9127U, D8127, D8126

Issue Is the NOTIFIER 911 Dialer programmable with a D5200 hand-held programmer? Solution Yes, the NOTIFIER 911 Dialer can be programmed with the D5200 Programmer. Use the D2071 handler.

If FSM needs to be connected to a new panel (network), then proceed as it is described in this article:

How to access the Menu features on the B926F which does not have a Menu button.

Part numbers, D344-RT (Remote Test Plate with Blue Test coil), D307 (Remote Test Plate), D341, D341P, D342, and D342P. How to correct the D344-RT not resetting the D341/D342 duct detector.