Security: Intrusion

Issue How is point expansion configured, addressed and wired on the D6112 panel? Solution Connections: 1.) Install the First Device to the D6112 control by connecting one of the two White leads to terminal 11 (Data- first device). The Black lead will land on terminal 14 (common) and the Red on terminal 15 (+ 12Vdc). This device will be programmed as DEVICE 1. 2.) Install the Second Device to the D6112 control by connecting one of its White leads to the remaining White lead from Device 1. The Black and Red leads of the second device will connect to Common and +12Vdc respectively. This device will be programmed as DEVICE 2. 3.) Each additional device will be installed by connecting its White wire to the previous device remaining white wire until the last device. The remaining White wire on the last device will connect to the D6112 control terminal 13 (Data- last device). Programming: 1.) Go to the Devices Module part of the D6112 handler and on line 4.1 Device#, select 1 for the first device. a) On line 2 D1 Model, select the device model code (1=D610/611, 2=D620/D626, 3=D630/D636A, 4=D640) that pertains to the first device. 2.) Continue by selecting 2 on line 4.1 Device# for the second device and on line 4.2 D1 Model, enter that device model code. Continue until all devices are programmed. 3.) Address the points according to the device they are expanded off of. The zone location is comprised of the Device model code and the zone. The zones are identified by letter starting with A for the first zone and counting up alphabetically. a) Onboard zones 1-8 use a device code of 0 and are addressed as 0A-0H. b) Zones 9 and up would be addressed 1A, 1B and so on. Note: It is not required that zones 1-16 be located on any particular device or in any particular order. It is advisable that the system be laid out in a logical order for future reference.

How to troubleshoot 'Receiver Error' on the D6412 or /D4412 control panel. D4412,D6412,RF3226

What relay configuration setting activates a relay with CMD 47?

How to select custom arming points on the D4412/D6412 Panel.

Issue When programming the phone number in a D4412/D6412 panel, how would a pause be entered in through keypad programming?   Solution   When a 4 second pause is needed while programming through the keypad, enter in a 13 for the nibble where you would like the pause to occur.

Overview Device Comm Error displays on the keypad.  Reports trouble zone 2. Wiring issue with the devices. Issue Device Comm Error displays on the D636 keypad. CS is receiving a Trouble zone 2 signal.   Solution   The devices (D636, D620, D640) have a wiring issue. All device data wiring should be connected in series. Example:  Data wire out from panel terminal 11 to the first device

Issue What are the SDI addresses on the D6412 and D4412?   Solution   SDI Address             Device Description 0 =           Installer Keypad, or local connection to RAM IV                         1-8 =          Command Center 1 to 8 40,41 =       DX8010 Telephone Control Module 50,51 =       RF Receivers 1, and 2 52-55 =      RF Keypads on RF Receiver 1 60-63 =       RF Keypads on RF Receiver 2 101-107 =   DX 2010 wired point expander 150-151 =   DX 3010 Octo-Output expander 250 =           DX4010 Serial RS-232 Interface module

D6412, D4412

Issue CMD40 System Trouble Report Codes Display -  COMMAND 40 Solution Keying COMMAND - 4 - 0 at the Command Center will replace the display of zone status on the four left indicator lights with a trouble report code.  If applicable, a second trouble report can be displayed by keying in another COMMAND 40 (the maximum number of troubles held in the buffer is two).  If no indicators light on the second COMMAND 40 entry, there is only one cause for each trouble report. After the panel is disabled/restarted, powered cycled, or serviced for the indicated system troubles, clear the system trouble memory by entering COMMAND 40 until no troubles are displayed.  Press any key to exit COMMAND 40 since it is not automatically exited upon alarm or trouble condition. Alarms and troubles will continute to report to the central station unabated. 2|4 : D5100 Communication Error / bad connection to programmer 1     : Faulted Zone 2     : Command Center Communication Err / noisy environment or wiring issue 1|2: Communication Failure / unable to communicate with central station 3     : RJ Jack Supervision / phone cord unplugged or wired incorrectly 1|3:   Aux Power Supervision / possible short on aux device or wiring 2|3:   AC Power Fail / Check transformer power and/or wiring 1|2|3:Battery Supervision / low or failing battery 4    :  Command Center Fault / Check wiring and/or programming 1|4:    Internal Hardware Fault / main system board failure 1|2|4: Missing Serial Device / check keypads and/or expander 3|4:    Device Programming Err / keypad or expander does not match programming. 1|3|4:  Internal Sofwtare Err / internal memory failure 2|3|4:  Checksum Fail / EEPROM Failure 1|2|3|4: System ROM Failure / Internal ROM Failure 

How to determine which pins of the RJ45 and RJ11 are used for Tip and Ring or Tip-House/Ring-House.

How to view the log file in the D4412 or D6412.

How to use the RF3341 Keypad on a D4412/D6412 Panel.

How to prevent data noise, crosstalk, EMI, RFI and AC Inductance in data wiring.

The D4412 or D6412 reports Data Bus Tamper Device 50 or 51 and the cover is in place and the cover tamper is closed on the RF3224. RF3224,D4412,D6412

How to configure an output for arming verification from an keyswitch point or RF keyfob.

How to correct the keypad displays "Entering" when powered up and then becomes "Keypad Locked". D6412,D4412,D623,D625,D623B

How to use CMD56 to add user codes to the D4412/D6412. When Using CMD56 to Add Codes, there is no prompt to Add Codes, Only Change Codes.

How to interpret a Battery Low report on the D4412/D6412. What battery voltage will the panel transmit a BATTERY LOW report?

How to disable Call Waiting on D4412/D6412 Panels.

How to access the D4412 or D6412 Event Log and how many events can it hold.