Bosch Building Technologies

    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Intrusion

    Sort by:
    ‎06-25-2018 04:15 PM
    What relay configuration setting activates a relay with CMD 47?
    View full article
    ‎06-21-2018 10:39 PM
    How to select custom arming points on the D4412/D6412 Panel.
    View full article
    ‎06-20-2018 10:34 PM
    Issue When programming the phone number in a D4412/D6412 panel, how would a pause be entered in through keypad programming?   Solution   When a 4 second pause is needed while programming through the keypad, enter in a 13 for the nibble where you would like the pause to occur.
    View full article
    ‎06-20-2018 07:42 PM
    Overview Device Comm Error displays on the keypad.  Reports trouble zone 2. Wiring issue with the devices. Issue Device Comm Error displays on the D636 keypad. CS is receiving a Trouble zone 2 signal.   Solution   The devices (D636, D620, D640) have a wiring issue. All device data wiring should be connected in series. Example:  Data wire out from panel terminal 11 to the first device
    View full article
    ‎06-20-2018 07:19 PM
    Issue What are the SDI addresses on the D6412 and D4412?   Solution   SDI Address             Device Description 0 =           Installer Keypad, or local connection to RAM IV                         1-8 =          Command Center 1 to 8 40,41 =       DX8010 Telephone Control Module 50,51 =       RF Receivers 1, and 2 52-55 =      RF Keypads on RF Receiver 1 60-63 =       RF Keypads on RF Receiver 2 101-107 =   DX 2010 wired point expander 150-151 =   DX 3010 Octo-Output expander 250 =           DX4010 Serial RS-232 Interface module
    View full article
    ‎06-20-2018 06:35 PM
    D6412, D4412
    View full article
    ‎06-19-2018 10:40 PM
    Issue CMD40 System Trouble Report Codes Display -  COMMAND 40 Solution Keying COMMAND - 4 - 0 at the Command Center will replace the display of zone status on the four left indicator lights with a trouble report code.  If applicable, a second trouble report can be displayed by keying in another COMMAND 40 (the maximum number of troubles held in the buffer is two).  If no indicators light on the second COMMAND 40 entry, there is only one cause for each trouble report. After the panel is disabled/restarted, powered cycled, or serviced for the indicated system troubles, clear the system trouble memory by entering COMMAND 40 until no troubles are displayed.  Press any key to exit COMMAND 40 since it is not automatically exited upon alarm or trouble condition. Alarms and troubles will continute to report to the central station unabated. 2|4 : D5100 Communication Error / bad connection to programmer 1     : Faulted Zone 2     : Command Center Communication Err / noisy environment or wiring issue 1|2: Communication Failure / unable to communicate with central station 3     : RJ Jack Supervision / phone cord unplugged or wired incorrectly 1|3:   Aux Power Supervision / possible short on aux device or wiring 2|3:   AC Power Fail / Check transformer power and/or wiring 1|2|3:Battery Supervision / low or failing battery 4    :  Command Center Fault / Check wiring and/or programming 1|4:    Internal Hardware Fault / main system board failure 1|2|4: Missing Serial Device / check keypads and/or expander 3|4:    Device Programming Err / keypad or expander does not match programming. 1|3|4:  Internal Sofwtare Err / internal memory failure 2|3|4:  Checksum Fail / EEPROM Failure 1|2|3|4: System ROM Failure / Internal ROM Failure 
    View full article
    ‎06-19-2018 10:10 PM
    How to determine which pins of the RJ45 and RJ11 are used for Tip and Ring or Tip-House/Ring-House.
    View full article
    ‎06-19-2018 09:29 PM
    How to view the log file in the D4412 or D6412.
    View full article
    ‎06-19-2018 09:22 PM
    How to use the RF3341 Keypad on a D4412/D6412 Panel.
    View full article
    100% helpful (1/1)
    ‎06-19-2018 03:06 PM
    How to prevent data noise, crosstalk, EMI, RFI and AC Inductance in data wiring.
    View full article
    ‎06-18-2018 09:38 PM
    The D4412 or D6412 reports Data Bus Tamper Device 50 or 51 and the cover is in place and the cover tamper is closed on the RF3224. RF3224,D4412,D6412
    View full article
    ‎06-18-2018 09:03 PM
    How to configure an output for arming verification from an keyswitch point or RF keyfob.
    View full article
    ‎06-18-2018 08:51 PM
    How to correct the keypad displays "Entering" when powered up and then becomes "Keypad Locked". D6412,D4412,D623,D625,D623B
    View full article
    ‎06-18-2018 08:39 PM
    How to use CMD56 to add user codes to the D4412/D6412. When Using CMD56 to Add Codes, there is no prompt to Add Codes, Only Change Codes.
    View full article
    ‎06-18-2018 06:55 PM
    How to interpret a Battery Low report on the D4412/D6412. What battery voltage will the panel transmit a BATTERY LOW report?
    View full article
    ‎06-26-2018 02:18 PM
    How to view the panel type and firmware revision.
    View full article
    ‎06-18-2018 06:35 PM
    How to disable Call Waiting on D4412/D6412 Panels.
    View full article
    ‎06-18-2018 06:13 PM
    How to access the D4412 or D6412 Event Log and how many events can it hold.
    View full article
    ‎06-17-2018 09:35 PM
    Issue User has authority in all areas but when presses Command 80, Command Center gives error tone and says Area 1 Ok for all on. Solution CMD 80 (All Areas On) and CMD 81 (All Areas Off) must be enabled in programming in order to function. 1)  Using Remote Programming: Go to Panel Wide Parameters; Global Open Close Options; Arming Options and find Enable Cmd 80 - All Areas All On, and Enable Cmd 81 - All Areas All Off and set both to Yes. 2)  Using Keypad Programming: Go to Nibble 1259 and enter 12 to enable both CMD 80 and CMD 81. Part numbers D4412, D6412, D625, D623
    View full article
    Top Contributors