Bosch Building Technologies

    Security: Intrusion

    Sort by:
    ‎07-24-2018 04:50 PM
    What functions can be performed with the RF3341 wireless keypad?
    View full article
    ‎07-24-2018 03:39 PM
    How to program point text into the D7112.
    View full article
    ‎07-19-2018 10:46 PM
    How to unbypass points on the D7112 panel.
    View full article
    ‎06-19-2018 09:45 PM
    How to make the DS7060 panel send a 3 digit account number.
    View full article
    ‎07-17-2018 10:17 PM
    How to change passcodes on the DS7100 control panel.
    View full article
    ‎07-17-2018 10:19 PM
    What is the expansion module for the DS7080IP32 panel?
    View full article
    ‎07-17-2018 06:24 PM
    How to enable/disabling encoding tones on the D1254 Keypad used wth the D7112.
    View full article
    ‎07-17-2018 02:50 PM
      How to perform Zone Test from a Master Keypad on the DS7400 Series. DS7400,DS7400X,DS7400Xi,DS7400Xi (Ver 3+),DS7400Xi (Ver 4+)  
    View full article
    ‎07-16-2018 10:15 PM
    How to determine the number of passcodes are available in the D7112. How many passcodes can the D7112 panel have?
    View full article
    ‎07-16-2018 10:11 PM
    How to determine how many command centers (keypads) are supported by the D7112. How many command centers can be supported on the D7112?
    View full article
    ‎07-16-2018 10:03 PM
    How to determine the capacity of the D7112 panel event log. How many events are held in the D7112 panel log?
    View full article
    ‎07-16-2018 04:46 PM
    How to configure the DS7400Xi Ver4+ for Direct Connection using RS232. DS7400XIVER4+,DX4010i, DX4010V2
    View full article
    ‎07-13-2018 09:56 PM
    How to make the DS7100 dial without waiting the 7 second delay.
    View full article
    ‎07-13-2018 09:33 PM
    How to disabling zones/Points on the DS7400 Series Panel. DS7400Xi (Ver 4+),DS7400,DS7400X,DS7400XIVER2,DS7400XIVER3+,DS7400XIVER4+,DS7400Xi (Ver 3+).
    View full article
    ‎07-11-2018 06:35 PM
    Issue What is the 8 zone expansion module that is used on the DS7080IP32 control panel?   Solution   The EX8 would be the 8 zone expander module used to expand the DS7080IP32 panel. This expander wires on the keypad bus and can be addressed as 9-16 with no jumper (module address 101) or 17-24 with a jumper across pins 1 (module address 102), or zones 25-32 with a jumper across pins 2 (module address 103). You must use 9-16 first and power must be cycled after address changes for them to take effect.
    View full article
    ‎07-11-2018 05:23 PM
    How to interpret the Alert Light flashing the DS7100 panel keypad after disarming. DS7140,DS7100.
    View full article
    ‎07-11-2018 03:23 PM
    How to 'Quick Arm' the DS7400XI Ver. 3+ control panel by pressing [#]+[ON] to arm.
    View full article
    ‎07-10-2018 08:58 PM
    Issue How can I get the panel to test the bell when the system is Armed? Solution In order to have the bell sound at the end of the Arming Sequence, you must follow the steps listed below: Put the system into program mode by either entering the INSTALLERS (Default is 98765) CODE # 0 or holding down the S1 pin on the middle of the control board down towards the bottom. Type in 81 # and see what the first data digit is and make a note of it. Ex. D1=1. Press # again to see what the second data digit is and make a note of it. Ex. D2=0. Press # again to see what the third data digit is and make a note of it. Ex. D3=7. Press # again to see what the fourth and final data digit is and make a note of it. Ex. D4=6 Ex  D1=1 D2=0 D3=7 D4=6 for a complete number of 1076. In order to have the system do the Bell test when arming you must make digit 2 a 2 or a 3 and the other digits will stay the same. 2 would give you the following: Test Bell but NOT the Phone line upon arming. 3 would give you the following: Test Phone line AND Bell upon arming. Now press the * twice to get you back to the ADR= and do the following: To make the change with the number 2 option you will press 811276# OR To make the change with the number 3 option you will press 811376# After that you can hold * down for 3 seconds, release it, and test the changes out.
    View full article
    ‎07-02-2018 10:24 PM
    Issue What is the process to set up auto arming on the DS7100?   Solution   To setup auto-arming perform the following steps: Enter a valid master code # 0,7 Enter address 05, then the auto arm time in 24 hour format then #. Example:  Auto arm at 10:30 PM.                Master PIN + #0 ,7,  05, 2300 #
    View full article
    ‎07-02-2018 10:22 PM
    Issue What are the steps on setting the panel time for the DS7100?   Solution   Enter in a valid master code # 0,7 Enter 01, then enter the time ( 24 hr. format ) then #
    View full article
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist