Overview: Keypad displays a flashing "service perimeter" because a zone is or was faulted.
Issue
Keypad displays a flashing "Service Perimeter" with no zones displayed.
Solution
A Perimeter zone is or was faulted.
If a zone is displayed, the zone must be made normal first.
If no zone is displayed, enter CODE + ENTER + CLEAR + CLEAR . This will clear the keypad memory.
Issue
What is the process to set up auto arming on the DS7100?
Solution
To setup auto-arming perform the following steps:
Enter a valid master code # 0,7
Enter address 05, then the auto arm time in 24 hour format then #.
Example: Auto arm at 10:30 PM.
Master PIN + #0 ,7, 05, 2300 #
How is the Chime Mode enabled?
DS7060,DS7080I,DS7080IP32,DS7080IVER2,DS7090,DS7090I,DS7090TM,DS7090TMI,DS7100,DS7400,DS7400X,DS7400X,DS7400Xi,DS7400Xi (Ver 3+),DS7400Xi (Ver 4+),DS7400XIVER2
How to determine correct wiring with between the DS7420i and different DS7400 panel types.
Is the wiring configuration between the DS7420i and DS7400 panel different than with the DS7400Xi?
DS7400,DS7400X,DS7400Xi,DS7420i.
How to determine the wiring requirements for the multiplex bus and zone loops.
DS7400X,DS7400,DS7400Xi,DS7400XIVER2,DS7400XIVER3+,DS7400XIVER4+,DS7461i,DS7460i,DS7465i,DS7457i,DS7432
Issue
Can not get some of the functions to work on the command center.
Overveiw: Some functions require you to enter single partition mode when using a master keypad.
Soultion
The following command require that you are in single partition mode when entering from a master keypad. ( valid code ## )
History read-back
Chime mode
Checking zone status
Checking zone troubles status
Bypassing zones
Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, DS7447, DS745, DS7447E,
Issue
What do the error displays mean on the DS7080i ?
Solution
Error Displays
Control panel problems are indicated by a flashing green Power Light.
The DS7447 display will also read “Control Trouble, Enter # 8 7.” The DS7445 will only flash the green Power Light.
The Error messages may only be read when the control is disarmed. Contact your installing company if the problems persist.
1.) DS7447 - “AC Power Failure”:
DS7445 - LED 1 turns on steady:
There is a power failure and the panel is operating on backup battery.
2.) DS7447 - “Battery Trouble”:
DS7445 - LED 2 turns on steady:
If the system has just been through a power failure, wait at least two hours for the battery to recharge, then enter a PIN + [System Reset] to perform a battery test.
3.) DS7447 - “Communicator Err”:
DS7445 - LED 3 turns on steady:
The communicator failed to communicate with the central station.
4.) DS7447 - “System Fault”:
DS7445 - LED 4 turns on steady:
Internal error in the control circuitry or optional circuitry. These faults are displayed as follows:
RAM Fault
ROM Fault
EEPROM Fault
TRBL Zone Fault.
5.) DS7447 - “Keypad Fault”:
DS7445 - LED 5 turns on steady:
One of the keypads is not responding to the control panel.
6). DS7447 - “Aux Power Fault”:
DS7445 - LED 8 turns on steady:
The auxiliary power has been shorted.
7.) DS7447 - “Zone Trouble”: DS7445 - LED 6 turns on steady:
One of the zones is not responding to the control panel. This may also be displayed during power-up (if so, ignore).
* = If in “Residential Mode”, a PIN is not required for these commands.
** = Battery Trouble and Communicator Err displays must be cleared by the [System Reset] command sequence even after the problem has been remedied. These displays will not self clear. All the other error displays will self clear from the keypads once the problem has been remedied.
Can the D125B be Used to Power 2 Wire Smokes on the D7112?
Yes, see technogram number (73-06116-000-C) 1993 (attached). Listings and Approvals Underwriters Laboratories lists the D7112 ControVCommunicator as a Digital Alarm Communicator Transmitter (DACT) for: NFPA 71 Central Station, NFPA 72 Chapter 6 Local, NFPA 72 Chapter 8 Remote Station, NFPA 74 Household Fire Warning. The D7112 also has the following Approvals: CSFM and NYC-MEA (formerly NYC-BSA).
