Security: Intrusion

How to prevent data noise, crosstalk, EMI, RFI and AC Inductance in data wiring.

How to determine how long the loop wiring can be or how many devices can be connected to a D9127. D9127U,D9127T,D8125

How to view the panel type and firmware revision.

How to use the Enter Key Relay function in G series panels.

How to interpret panel reports generated by MISSING Point Events on G Series Panels.

How to Enable Alarm Verification and how it works.

Issue Can I mix Heat Detectors and 2 wire smokes with a sounder when using a D132A Smoke Detector Polarity Reversing Module? Solution No. When a Heat detector goes into alarm it puts a short on the input zone to indicate the alarm. The D132A uses Aux power from the panel when the polarity reversal takes place and since a heat detector does not reset when polarity is reversed, it would put a direct short on the Aux power of the panel. Consequently everything connected to the same Aux power terminals would not function.

Overview When wireless points are faulted, they display as 'Short' to the panel. When the wireless point tamper switch is faulted it will display as an 'Open' to the panel. Issue The panel when using a D8125INV and wireless points shows normal/faulted when point transitions from normal to off normal but the control always shows shorted. Solution Problem may be caused by another point expander connected to the control panel. Remove D8125INV from control panel and determine if points go missing. If points remain active (normal, faulted, etc) the control panel is interfacing with the points through another addressable point expander. Part numbers D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G, D8125INV, ISW-D8125CW, ISW-D8125CW-V2, FA400, EN4200

Issue What is the difference between the D133 an D134? Solution The D133 has a single relay rated at 2A @ 30 VDC – 0.6A @ 125 VAC. The D134 has two relays rated at 2A @ 30 VDC – 0.6A @ 125 VAC. Current draw for the Relay is 40 mA per relay when activated.

How to determine why the BFSK/Relay or Output selected in Point Assignments, or points configured with Relay Response=2, do not reset as expected.  

Part numbers D7412, D9412, D7412G, D9412G, D7412GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B6512, B8512G, B9512G, D9210, D9210B, D9210C, B901

How to correct when the command center goes blank as soon as the last area arms. Why does the command center goes blank as soon as the last area arms?

How to configure the Swinger Count and use Swinger Shunt.

How To Transmit Opening/Closing Reports By Account Number.

How to transmit opening/closing reports when arming individual areas.

How to make a relay trip when a point is faulted. How to use Relay Follow Point, Output Response type or Relay Response Type.

How to prevent arming Perimeter Delayed when attempting to Master Arm. The keypad Shows Perimeter Delayed after Arming with a Passcode and Enter.

How to lock access to the panel program to prevent take overs. D9112B1, D2012, D2112, D2212, D2412, D2812, D7212B, D7212B1, D8112G2L, D9112, D9112B, D9112B1

Article describes the "alarm panel substitution" message

How to latch the Summary Fire Relay of a D7000/9000 and G Series control panel. Fire Summary Sustain