Security: Intrusion

How to locate the various connections and controls on the D636A keypad.

How to interpret a BROKEN Amber Circle on the EZ Series panel keypad.

  How to checking system troubles on D6412 & D4412 using a D623 or D625 keypad.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3,D7412GV3, D9412GV3, D7212GV4, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G

How to use the RF3341 Keypad on a D4412/D6412 Panel.

How to access the Menu features on the B915 which does not have a Menu button.

The Alpha keypad offered for the D8112 panel series was the D1252 or D1252A   Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2, D1252, D1252A

Issue How is point expansion configured, addressed and wired on the D6112 panel? Solution Connections: 1.) Install the First Device to the D6112 control by connecting one of the two White leads to terminal 11 (Data- first device). The Black lead will land on terminal 14 (common) and the Red on terminal 15 (+ 12Vdc). This device will be programmed as DEVICE 1. 2.) Install the Second Device to the D6112 control by connecting one of its White leads to the remaining White lead from Device 1. The Black and Red leads of the second device will connect to Common and +12Vdc respectively. This device will be programmed as DEVICE 2. 3.) Each additional device will be installed by connecting its White wire to the previous device remaining white wire until the last device. The remaining White wire on the last device will connect to the D6112 control terminal 13 (Data- last device). Programming: 1.) Go to the Devices Module part of the D6112 handler and on line 4.1 Device#, select 1 for the first device. a) On line 2 D1 Model, select the device model code (1=D610/611, 2=D620/D626, 3=D630/D636A, 4=D640) that pertains to the first device. 2.) Continue by selecting 2 on line 4.1 Device# for the second device and on line 4.2 D1 Model, enter that device model code. Continue until all devices are programmed. 3.) Address the points according to the device they are expanded off of. The zone location is comprised of the Device model code and the zone. The zones are identified by letter starting with A for the first zone and counting up alphabetically. a) Onboard zones 1-8 use a device code of 0 and are addressed as 0A-0H. b) Zones 9 and up would be addressed 1A, 1B and so on. Note: It is not required that zones 1-16 be located on any particular device or in any particular order. It is advisable that the system be laid out in a logical order for future reference.

How to add the security company phone number to display on the D1260 Enhanced Command Center.

How to use expanded points on the B921C or B942 SDI2 Keypad. Part numbers B921C, B942, B3512, B4512, B5512, B6512, B8512G, B9512G, D7412GV4, D9412GV4

How to use the A or B or C keys on 2000 series panels.

 How to work with the D279A Independent Zone Controller.

1.  Ensure the area is disarmed. 2.  Press Cmd + 4 + 2.  The flashing Cmd light is a prompt to enter a valid passcode.  3.  Enter a valid passcode and the D621 displays system trouble events by lighting the point indicators (zone leds)as described below:  Zone 1 Lit steady = Telephone line Fail  Zone 1 Slow Flash = Comm Fail, Destination 1  Zone 1 Fast Flash = Comm Fail, Destination 2  Zone 2 Lit steady = Alternate Comm Trouble  Zone 3 Lit steady = Installer Switch Closed  Zone 4 Lit steady = Backup Battery low  Zone 4 Lit steady = Slow Flash = Backup Battery Missing  Zone 5 Lit steady = Bell Supervision Fail  Zone 6 Lit steady = RF Receiver Jamming  Zone 6 Slow Flash = RF Receiver Trouble  Zone 7 Lit steady = Data Bus Device Missing  Zone 7 Slow Flash = Data Bus Device Tamper  Zone 7 Fast Flash = Data Buss Device Trouble/Reset  Zone 8 Lit steady = System Fault  Zone 8 Slow Flash = Service Interval  Zone 8 Fast Flash = Ground Fault Condition Press Cmd to return to the off state.

How to enable/disabling encoding tones on the D1254 Keypad used wth the D7112.

  How to perform Zone Test from a Master Keypad on the DS7400 Series. DS7400,DS7400X,DS7400Xi,DS7400Xi (Ver 3+),DS7400Xi (Ver 4+)  

The keypad will display ‘Command Disabled’ when the Menu key is pressed for one of the following reasons. If the menu item # 1 in the function list is set with a function 0 and marked yes for any Command Center. If all of the Functions for the Command Center are selected as No (disabled). To prevent the keypad from displaying ‘Command Disabled’ after selecting Menu; Select a non-zero value for the Function # of Menu Item 1. Ensure that at least one of the Menu Items intended for use are set as Yes.

Issue What is the difference between the D623B and the D623 keypads for the D4412/D6412 panels?   Solution The only difference is the D623B is the new Bosch design keypad with a Grey Faceplate for D4412/D6412 panels. See photo below.