Security: Intrusion

Part numbers D2212, D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U, D2812P

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3,D7412GV3, D9412GV3, D7212GV4, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G

Part numbers D2212, D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U, D2812P

Issue The Panel will not arm by entering the PASSCODE, VERIFY ID, ALL ON/OFF. Solution On this panel for the ALL ON/OFF key to work CMD 1, CMD 2, and CMD 3 must be set to yes in the Arming Commands part of the program in the MAIN.

Issue If using the D220A on the D2112 do I have the Exit Feature? Solution No, the D2112 does not have the Exit Feature. It uses the "Step Out Feature". The Exit Feature does appear on page 23 of the Users Guide, but that is because this Keypad can also be used on other 2000 Series Panels which have the Exit Feature.

Issue How can I tell if the D168 will work with my control? Solution There are 3 items that are important when determining if it will be fully compatible with the control that is in question. 1. The control must provide a 12 volt dc aux power source to the D168A. 2. The control must have the ability to program a point as a keyswitch point. This only applies if you want to arm/disarm through the phone. Otherwise, you will just get arm/disarmed status. The keyswitch point can be programmed as momentary or maintained. 3. The control must have the ability to program a trigger that will trip and stay tripped  when the system is armed.           

Part numbers D2212, D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U D2812P, D168A

Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, D8112, D8112E, D8112E1, D8112G, D8112G1, D8112G2, D8112A

Part numbers D1252, D1252A, D8112A, D8112, D8112E, D8112E1, D8112G, D8112G1, D8112G2

Issue What are the dip switch settings for sensitivity adjustments on the DS794Z? Solution The DS794Z comes in 2 versions, one of which has a bank of 5 Configuration switches and an older version that has a bank of 8 Configuration switches. *Bank of 5 Configuration switches Switch 2 On, 3 On= Standard Sensitivity Switch 2 Off, 3 On= Intermediate Sensitivity Switch 2 On, 3 Off= High Sensitivity   **Bank of 8 Configuration switches Switch 5 On, 6 Off= High Sensitivity Switch 5 Off, 6 On= Intermediate Sensitivity Switch 5 On, 6 On= Standard Sensitivity

Part numbers D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3,D7412GV3, D9412GV3, D7212GV4, D7412GV4, D7412GV4, D9412GV4

Issue How can Force Arming the D4412/D6412 be disabled on Command Centers? Solution It is not possible to disable force arming on keyfobs. To disable force arming at Command Centers on the D4412/D6412: 1) Go to PANEL WIDE PARAMETERS, Global Open/Close Options and Arming Options and find 'Bypass/Force Arm Limit and change from Unlimited (default) to 1 Point. 2) Go to POINT PARAMETERS and Point Index Configuration. For all programmed points in the panel, ensure Bypass/Force Arm (Yes/No) is set to No.

     

     

How to activate the Area Armed or Perimeter Armed Relay at the beginning of the exit delay.

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+,

 How to work with the D279A Independent Zone Controller.

Issue How may users can the Easy Series panel hold?   Solution   The panel will hold up to a total of 22 users: 1:  Master user 2 to 21: System users User 22: Duress user

Issue Keypad displays check zone, then displays the zone number.   Solution   Check followed by zone# or zone #'s indicates which points must be tested or bypassed before arming the system. Any zone on the control can be programmed to check before arming as well as multiple zones. Some systems are programmed this way to check for proper operation of the zone or zone's before it will allow you to arm. To disable this feature follow directions below. 1. Enter pgm mode A. At the keypad enter the 5 digit programmers code followed by #0 ie... 98765#0, should now be in program mode (Led keypad will toggle leds back and forth)(alpha keypad will display program mode). If not, press the S1 switch located above zone 1 on the control. B. Once in program mode enter 20 00000# C. Press the * key for 3 seconds and release it. Should now be out of program mode. Reattempt to arm the system.