Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Intrusion

    Sort by:
    ‎06-25-2018 04:21 PM
    Issue How is point expansion configured, addressed and wired on the D6112 panel? Solution Connections: 1.) Install the First Device to the D6112 control by connecting one of the two White leads to terminal 11 (Data- first device). The Black lead will land on terminal 14 (common) and the Red on terminal 15 (+ 12Vdc). This device will be programmed as DEVICE 1. 2.) Install the Second Device to the D6112 control by connecting one of its White leads to the remaining White lead from Device 1. The Black and Red leads of the second device will connect to Common and +12Vdc respectively. This device will be programmed as DEVICE 2. 3.) Each additional device will be installed by connecting its White wire to the previous device remaining white wire until the last device. The remaining White wire on the last device will connect to the D6112 control terminal 13 (Data- last device). Programming: 1.) Go to the Devices Module part of the D6112 handler and on line 4.1 Device#, select 1 for the first device. a) On line 2 D1 Model, select the device model code (1=D610/611, 2=D620/D626, 3=D630/D636A, 4=D640) that pertains to the first device. 2.) Continue by selecting 2 on line 4.1 Device# for the second device and on line 4.2 D1 Model, enter that device model code. Continue until all devices are programmed. 3.) Address the points according to the device they are expanded off of. The zone location is comprised of the Device model code and the zone. The zones are identified by letter starting with A for the first zone and counting up alphabetically. a) Onboard zones 1-8 use a device code of 0 and are addressed as 0A-0H. b) Zones 9 and up would be addressed 1A, 1B and so on. Note: It is not required that zones 1-16 be located on any particular device or in any particular order. It is advisable that the system be laid out in a logical order for future reference.
    View full article
    ‎06-25-2018 04:20 PM
    How to troubleshoot 'Receiver Error' on the D6412 or /D4412 control panel. D4412,D6412,RF3226
    View full article
    ‎06-25-2018 04:15 PM
    What relay configuration setting activates a relay with CMD 47?
    View full article
    ‎06-25-2018 04:06 PM
    How to program Passcode Duress on the D7212B,  D7212B1, D9112B or D9112B1
    View full article
    ‎06-25-2018 03:50 PM
      Issue The D192G panel zone (point) is in trouble and the yellow LED is not on. Solution With the zone/point in trouble and No Yellow LED On there is a wiring fault. One of the following terminals do not have power connected to them. External Power In (EXT PWR IN) Auxiliary Power In (AUX PWR IN) Terminal 1 (AUX PWR IN) 13.75 VDC Terminal 2 (Common) Terminal 3 (Supervised Zone / Point) 2.50 VDC Normal Condiction < 1.50 VDC In Trouble Condiction Terminal 4 (Trigger) 13.75 VDC  In Alarm Only Terminal 5 (External Power In) 12 VDC or 24 VDC Depended on needed Output for the NAC's or Power Supply Terminal 6 (Common) This is the Common from an 24 VDC External Power Terminal 7 (Positive Alarm Output) Terminal 8 (Negative Alarm Output)
    View full article
    ‎06-25-2018 03:44 PM
    Issue The D279 or D279A will not recover the default passcode while following the instructions. Solution You are performing this procedure while one of the D279A zones is not in a normal condition. Normalize D279A zones and the default procedure will work.      
    View full article
    ‎06-25-2018 03:36 PM
    Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+,
    View full article
    ‎06-25-2018 03:26 PM
    How to interpret the WDSRP log entry: ARMED LEVEL 2 from a DS7060 control panel.
    View full article
    ‎06-25-2018 03:20 PM
    D7112 Overview: Firmware Revision 3.57 is NOT compatible with the D7112 panels with a date code of X9416 or higher.   Issue   Panel is non responsive to any programming.   Solution   Firmware Revision 3.57 is NOT compatible with the D7112 panels with a date code of X9416 or higher.
    View full article
    ‎06-25-2018 03:13 PM
    Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+,
    View full article
    ‎06-25-2018 03:07 PM
    Issue What are the steps on silencing the fire alarm, and resetting the control panel? Solution Present your token twice, or enter your pass code twice.
    View full article
    ‎06-25-2018 03:02 PM
    Issue What are the wire length limits for the command center?   Solution   Minimum wire length = 10 feet Maximum wire length = 328 feet
    View full article
    ‎06-25-2018 02:57 PM
    Issue Unable to get the token reader to work when the UI is mounted to a metal surface. Solution The IUI-EZ1 cannot  be mounted directly to a metal surface. The UI needs to be separated by at least 3 inches of non-conductive material between the metal surface.
    View full article
    ‎06-22-2018 09:43 PM
    How to program the test report on a D9000, G Series, or GV2 Series control panel.
    View full article
    ‎06-22-2018 09:19 PM
    How to bypass the tamper input on the DX2010.
    View full article
    ‎06-22-2018 09:14 PM
    How to determine the wiring requirements for the multiplex bus and zone loops. DS7400X,DS7400,DS7400Xi,DS7400XIVER2,DS7400XIVER3+,DS7400XIVER4+,DS7461i,DS7460i,DS7465i,DS7457i,DS7432
    View full article
    ‎06-22-2018 08:29 PM
    How to correct the error message  "RAM CARD NOT PRESENT" when updating D5200 handlers.
    View full article
    ‎06-22-2018 08:08 PM
    How to correct zones not showing faulted in disarm state on of D4112/D6112 panel keypad. D6112,D4112,D420A (6 led),D620,D636A.
    View full article
    ‎06-22-2018 07:25 PM
    How to correct the D8128A is inoperative when wired according to terminal labeling. D7212B,D7212B1,D9112B,D9112B1,D8129,D7112
    View full article
    ‎06-22-2018 03:37 PM
    I just replaced my external modem with a new one, and when connecting to a panel the status screen never moves from (configuring port). D5500C-LITE-LPT,D5500C-LITE-USB,D5500C-LPT,D5500C-USB,D5500CU,D5500CU-LITE,RAM,RAM IV - D5370,RAMIV,RAMIV LITE,RPS,RPS LITE
    View full article
    Top Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist