Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Intrusion

    Sort by:
    ‎07-27-2018 08:25 PM
    How to correct D6200 software returns Communication Failed by Error when connecting to the receiver. D6600 D6100IPv6 D6200-CD
    View full article
    ‎07-30-2018 07:43 PM
    Issue How many 2 wire smokes will the D7112 support on zone 1?   Solution   Manufacturer & Models, and the number of smokes Radionics D262 with the D260 base  = 20 smokes DS200 with the MB200-2w base  = 10 smokes System Sensor 1400   =  10 smokes System Sensor 2400  = 10 smokes System Sensor 2400TH  = 10 smokes System Sensor 1451 with the B401 base  = 10 smokes System Sensor 1451 DH with the DH400 base  = 10 smokes System Sensor 2451 with the B401,B401B or DH400  = 10 smokes System Sensor 2451TH  with the B401,B401B or DH400  = 10 smokes System Sensor 2300T  = 10 smokes
    View full article
    ‎07-27-2018 08:15 PM
    How to connect to RPS using the IP Communicator.
    View full article
    ‎07-30-2018 07:43 PM
    Issue What are the Dimensions of the Bosch D56 Command Center Keypad Conduit Box?   Solution   The Back Box Dimensions are 1 1/2" X 4 9/16" X 8 1/4".
    View full article
    ‎07-30-2018 07:43 PM
    Issue Does the D2112Command Centerbuzz discontinue after AC power is restored? Solution Yes. The Command Centertrouble buzz will timeout after 30 to 45 seconds following restoration of AC power.
    View full article
    ‎07-27-2018 07:03 PM
    How to troubleshoot the RS Control app display System is Disabled.
    View full article
    ‎07-27-2018 06:58 PM
    How to select the correct legacy mode or datagram setting for network communications.
    View full article
    ‎07-27-2018 06:35 PM
    How to determine which control panel has SDI 92 available for the IP Communicator. Which is the first panel that supported address 92 for communication devices on the SDI bus. B420, B426, B450
    View full article
    ‎07-27-2018 07:36 PM
    How to use the ISW-D8125CW-V2 and D8125INV on the same panel. Can the D8125INV be connected to a panel that already has an ISW-D8125CW-V2 connected?
    View full article
    ‎07-27-2018 06:03 PM
    How to configure the B426 or B420 IP Communicator using keypad programming.
    View full article
    ‎07-27-2018 07:34 PM
    Issue Why does the zone light on the D360 Command Center light when the D279A is disarmed? Solution The D8112 panel is programmed with a zone code of 3271 on a particular zone. The purple jumper on the D279A is cut. As a result, the D360 zone light illuminates when the D279A is disarmed. This is normal and will not impact the D8112 arming process.  If the D1252A is used, the disarm state of the D279A is not indicated.
    View full article
    ‎07-27-2018 07:32 PM
    How to Capture and Save a DX4020-G Log file for troubleshooting
    View full article
    ‎07-27-2018 05:11 PM
    Overview: Time needed to charge a 12 volt back up battery connected to a D4112 Issue   How long does it take to charge a back up battery connected to the panel for the first time?   Solution   It may take as long as 12 hours. BOSCH recommends that the battery be charged prior to the installation.
    View full article
    ‎07-27-2018 05:11 PM
    Overview: Power up charging status of the battey on a D4112 panel will send a trouble Zn 9 during Recharge cycle. Issue Why does the panel send a Trouble Zn 9 when the battery is charging?   Solution   After the AC is restored the battery will begin to charge.  When the battery reaches a charging level of 11.1 volts, and maintains battery voltage level above 10.3 volts for 1 minute, the panel will RESET and a battery trouble (Trouble Zn 9) will be sent to the Central Station.  When the battery reaches the charging level of 12.5 volts a Restoral Zn 9 is sent to the Central Station.    
    View full article
    ‎07-27-2018 05:10 PM
    Issue Will the D7112 support a daily 12:00 AM timer test ? Solution Not recommended. If the daily test timer is set for midnight ( 12:00 A.M. ) the panel stops reporting the daily test on January 1st.
    View full article
    ‎07-27-2018 05:10 PM
    Issue When do the D7112 Transmitters send a Low Battery Report? Solution For the Transmitters that use the 3.6V Lithium battery (D7121, D7122, D7130, D7131, D7198, and D7199), the low battery threshold is 3.4V.   For the transmitters that use the 9V Alkaline battery (D7190, D7191), the low battery threshold is 7.2V.
    View full article
    ‎07-27-2018 05:09 PM
    Issue Setting up the duress code on the DS7400XI 3+. Solution 1. Enter the program mode A. At the master keypad, enter the programmers code + #0. Ie...9876#0 Keypad should display: Prog.mode, the version and adr = 2. Enter a (2) digit report code in address 0322. Ie...032210#; this would be an example of a valid entry for the contact id mode. 3. Exit program mode A. At the keypad press and hold the star(*) key for 3 seconds and release it. You now should be out of the program mode, keypad should not display prog. mode anymore. 4. Assign the duress code to an available user #. A. At the keypad enter a master code followed by #0. Keypad now should scroll through an options menu. B. Press 0 then follow the instructions on the keypad. A duress code is authority level 5. Test the duress. The system should be armed and the exit delay time expired when disarming with the duress.
    View full article
    ‎07-27-2018 05:09 PM
    Overview: Firmware revision 2.20 and higher limit errors when keypad programming a D2212 panel for D208 point expansion.  Issue Why does the D2212 panel not allow keypad programming for a D208 point expander? Solution Before firmware revision 2.20, it was NOT possible to program the D2212 for a D208 Point Expander using keypad programming.  Panels before firmware version 2.20 should be programmed with the D5200 handheld programmer or RAMIV/RPS download software.  Firmware revision 2.20 and above CAN be programmed via the keypad.
    View full article
    ‎07-27-2018 03:06 PM
    Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G
    View full article
    ‎07-27-2018 03:06 PM
    Issue Enabling encryption on the DX4020 module. Solution Telnet into the DX4020 using the IP Address ported to port 9999. (Ex: Telnet xxx.xxx.xxx.xxxx 9999, where xxx.xxx.xxx.xxxx is the IP address of the DX4020 .).  Follow the procedure below: Press Enter to go into setup mode appears, Press the Enter key. Select 6- Security from the main menu and follow the next steps: At Disable SNMP (N) N press [ENTER]. At SNMP Community Name ( 😞 press [ENTER]. At Disable Telnet Setup (N) N press [ENTER]. At Disable Port 77FEh (N) N press [ENTER]. At Disable Web Server (N) N press [ENTER]. At Disable ECHO ports (Y) Y press [ENTER]. At Enable Encryption (N) press [Y]. At Key length in bits (0), type 128 and press [ENTER]. Change keys (N) press ‘Y’ to change it. Enter keys the bytes programmed in the D6680-E120. These 16 bytes (32 characters) should match.  Default value is 01-02-03-04-05-06-07-08-09-10-11-12-13-14-15-16. At Enable Enhanced Password (N) press [ENTER]. Select 9 at the main menu to save and close telnet session. A message is displayed the connection was lost..
    View full article
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist