Security: Intrusion

Issue What is the Part # for the ribbon cable that is used with the D128 or D928? Solution Call Spare Parts (800) 894-5215 - Ribbon Cable Part Number is 15-03131-000-B.

Issue Setting up the duress code on the DS7400XI 3+. Solution 1. Enter the program mode A. At the master keypad, enter the programmers code + #0. Ie...9876#0 Keypad should display: Prog.mode, the version and adr = 2. Enter a (2) digit report code in address 0322. Ie...032210#; this would be an example of a valid entry for the contact id mode. 3. Exit program mode A. At the keypad press and hold the star(*) key for 3 seconds and release it. You now should be out of the program mode, keypad should not display prog. mode anymore. 4. Assign the duress code to an available user #. A. At the keypad enter a master code followed by #0. Keypad now should scroll through an options menu. B. Press 0 then follow the instructions on the keypad. A duress code is authority level 5. Test the duress. The system should be armed and the exit delay time expired when disarming with the duress.

Overview: Firmware revision 2.20 and higher limit errors when keypad programming a D2212 panel for D208 point expansion.  Issue Why does the D2212 panel not allow keypad programming for a D208 point expander? Solution Before firmware revision 2.20, it was NOT possible to program the D2212 for a D208 Point Expander using keypad programming.  Panels before firmware version 2.20 should be programmed with the D5200 handheld programmer or RAMIV/RPS download software.  Firmware revision 2.20 and above CAN be programmed via the keypad.

Issue Panel is not sending restorals when the point restores.  Log also has no entries for restorals on the point.   Solution   This is normal if the panel is programmed not to send restorals. In RAM/RPS check in the following: Point Index Codes > Point Indexes 1-16 or Point Indexes 17-31 Disable Restorals Default: No    Selections: Yes or No Yes: Disable restoral reports for this point. No: Enable restoral reports for this point. When this option is enabled, a restoral report is sent to the receiver when the point returns to normal after being in an alarm or trouble condition. If you are using the 5200: In the 5200 check under: 9112B > Point Index > Point Index # (where # is a value between 1 and 31 only) press the white ENTER key press the down arrow key (red keys on the 5200) Repeat until you are at P## Disable Restorals Default: No Selection: Yes or No Yes = Disable Restoralreports for this point. No =  Enable Restoralreports for this point. When this option is enabled, a Restoral report is sent to the receiver when the point returns to normal after being in an alarm or trouble condition. Use this item to automatically put this point back into the system.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G

Issue Enabling encryption on the DX4020 module. Solution Telnet into the DX4020 using the IP Address ported to port 9999. (Ex: Telnet xxx.xxx.xxx.xxxx 9999, where xxx.xxx.xxx.xxxx is the IP address of the DX4020 .).  Follow the procedure below: Press Enter to go into setup mode appears, Press the Enter key. Select 6- Security from the main menu and follow the next steps: At Disable SNMP (N) N press [ENTER]. At SNMP Community Name ( 😞 press [ENTER]. At Disable Telnet Setup (N) N press [ENTER]. At Disable Port 77FEh (N) N press [ENTER]. At Disable Web Server (N) N press [ENTER]. At Disable ECHO ports (Y) Y press [ENTER]. At Enable Encryption (N) press [Y]. At Key length in bits (0), type 128 and press [ENTER]. Change keys (N) press ‘Y’ to change it. Enter keys the bytes programmed in the D6680-E120. These 16 bytes (32 characters) should match.  Default value is 01-02-03-04-05-06-07-08-09-10-11-12-13-14-15-16. At Enable Enhanced Password (N) press [ENTER]. Select 9 at the main menu to save and close telnet session. A message is displayed the connection was lost..

Issue What is RPS Call Back? Solution RPS Call Back Default setting is No. Selections are Yes or No Parameter Description Using this function allows the control panel, after it has verified the RPS passcode, to provide an additional level of security by hanging up and dialing the RPS phone number to call RPS at the central station prior to allowing any upload or download. Important: When using the RPS Callback function, enter a "C" as the last digit in the RPS phone number if DTMF dialing is used. Parameter Options Yes: When the control panel hears the proper RPS passcode, it hangs up the phone, seizes the phone line, then dials the programmed RPS phone number (see RPS Ph ). This ensures that only the control panel communicates with the RPS PC connected to the dialed phone number. No: The RPS session is initiated immediately; no call back is required. The control panel engages in RPS sessions when called from any phone number and a proper RPS passcode is identified.

Issue When looking at the history log on a D6412 or D4412, the history log displays user 255 key-switch, and the key-switch zone has not been enabled. Solution When arming with command 1, or pressing the all on key, and not using a pass code, "user 255 key-switch arming" will appear in the history log as the user that armed the system.

Issue When programming the D279 keypad point index on the 7000/9000, G, GV2, & GV3 series panels, how should the type and response be programmed?   Solution   Program a type 7 for D279 (O/C Non-Priority): The D279 provides point arming and disarming independent of the area arm state. A non-priority D279 point arm state does not affect the area arm state. Point Response must be programmed 1. Program type 8 for D279 (O/C Priority): The D279 provides point arming and disarming independent of the area arm state. A priority D279 point must be armed before an area can be armed. Program Point Response as 2.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3,

Issue What 2 wire smoke detectors have been UL listed compatible with the D4112?   Solution   Note : The D4112 is not UL listed for Commercial Fire Applications. This control does not support multiple detectors in alarm. Do not use smoke detectors from different manufacturers on the same circuit. Radionics Head  D262 / Base D260 (20 per loop) Detection Systems Head  DS200 / Base MB200-2W (10 per loop) Head DS200HD / Base MB200-2W (10 per loop) System Sensor Head 1400 / Base N/A (10 per loop) Head 2400 / Base N/A (10 per loop) Head 2400th / Base N/A (10 per loop) Head 1451 / Base B401, B401B (10 per loop) Head 1451DH / Base DH400 (10 per loop) Head 2451 / Base B401, B401B, DH400 (10 per loop) Head 2451TH / Base B401, B401B, DH400 (10 per loop) Head 2300T / Base N/A (10 per loop)

             

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, 

       

Issue What is the part number for the back up battery for the DS415i and the DS445? Solution The P333 Backup Battery is designed for use with both the DS445 and DS415i Photoelectric Beam Detectors. When using the P333 with the DS415i, the polarity plug in the battery connector must be removed. Pull the white plug out of the connector using a pair of needle nosed pliers before connecting it to the DS415i. When the P333 battery is used with the DS445, there are no modifications necessary.   Part numbers P333, DS445, DS415i  

Part numbers D2212, D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U, D2812P, D222A, D223A, D202A, D220A

Part numbers D7412,D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2,D7412GV3, D9412GV3,

This article explains how to re-enable access to the menus in TeraTerm for the B450.