Security: Intrusion

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+,

The D4412 or D6412 reports Data Bus Tamper Device 50 or 51 and the cover is in place and the cover tamper is closed on the RF3224. RF3224,D4412,D6412

How to configure an output for arming verification from an keyswitch point or RF keyfob.

How to correct the keypad displays "Entering" when powered up and then becomes "Keypad Locked". D6412,D4412,D623,D625,D623B

How to use CMD56 to add user codes to the D4412/D6412. When Using CMD56 to Add Codes, there is no prompt to Add Codes, Only Change Codes.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G, D1260

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G , B901, D9210B, D9210C

How to interpret a Battery Low report on the D4412/D6412. What battery voltage will the panel transmit a BATTERY LOW report?

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G,

How to view the panel log file using the DS7447 keypad. DS7400X,DS7400,DS7400Xi,DS7400XIVER3+,DS7400XIVER4+,DS7400XIVER2,DS7447I,DS7447E,DS7447

How to view the panel type and firmware revision.

How to disable Call Waiting on D4412/D6412 Panels.

How to access the D4412 or D6412 Event Log and how many events can it hold.

How to correct when keypads Display 'Serial IF Fault'. DS7447E,DS7447,DS7447I,DS7400XIVER3+,DS7400XIVER4+,DS7400Xi,DS7400XIVER2.

How to interpret Missing Command 7 or Command 9. Why are points 72 or 136 showing as MISSING in view point status? Why are points 128 or 248 showing as MISSING in view point status? D7212B,D7212B1,D9112B,D9112B1

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, DS7420i

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4,

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G,

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G

Issue User has authority in all areas but when presses Command 80, Command Center gives error tone and says Area 1 Ok for all on. Solution CMD 80 (All Areas On) and CMD 81 (All Areas Off) must be enabled in programming in order to function. 1)  Using Remote Programming: Go to Panel Wide Parameters; Global Open Close Options; Arming Options and find Enable Cmd 80 - All Areas All On, and Enable Cmd 81 - All Areas All Off and set both to Yes. 2)  Using Keypad Programming: Go to Nibble 1259 and enter 12 to enable both CMD 80 and CMD 81. Part numbers D4412, D6412, D625, D623