Security: Intrusion

Overview RF3401 wireless point always shows an open state, will need to be reprogrammed in the normal state.   Issue   RF3401 wireless transmitter using the External contacts stays open all the time (no change of state). Solution Transmitter must be deleted and relearned with the External point in the NORMAL state.

Part numbers RF1000, RF3212, RF3222, RF3224

How to configure the DX4020 for DHCP.

Issue How many zones can be programmed on the D8112G2?   Solution   The D8112G2 is capable to have 8 master zones that may be expanded to 134 individual zones of protection.

Issue What is the part number for the back up battery for the DS415i and the DS445? Solution The P333 Backup Battery is designed for use with both the DS445 and DS415i Photoelectric Beam Detectors. When using the P333 with the DS415i, the polarity plug in the battery connector must be removed. Pull the white plug out of the connector using a pair of needle nosed pliers before connecting it to the DS415i. When the P333 battery is used with the DS445, there are no modifications necessary.   Part numbers P333, DS445, DS415i  

How to interpret the keypad display: 9210 Not Ready. D9210B,D9210C, B901

How to use the D4412/D6412 for only Wireless Panic points.   When none of the wireless panics will trip into alarm.   

Definition: Watch Mode Only- This point will not create alarm or trouble responses and will not generate reports to the Central Monitoring Station.  Program the Point: Select Point Type= 0. Select all Yes/No options= NO. Set Alarm Report Routing = 0: No Reports, No Events to Log/Printer. Set Restoral Report Routing = 0: No Reports, No Events to Log/Printer. Select Watch Tone and enable Watch Point: Select [Cmd] + 62 to select the watch tone. Select [Cmd] + 63 to select the watch point(s).

Issue What are the enviromental considerations for the proper operation of the Bosch control/communicators? Solution Indoor Dry.   Relative Humidity 5% to 85% noncondensing at +86 degrees Fahrenheit (+30 degrees Celsius). Operating temperature would be +32 degrees Fahrenheit to +120 degrees Fahrenheit ( 0 degrees Celsius to 49 degrees Celsius ).

Will the receiver try different ACK tones if a tone has already been established for the given Caller ID number with handshake optimization?

Issue The D8112 panel is not sending signals when modem format is selected to the Central Station. Solution Only the D8112G2 can send signals in Modem II format with a CS setting of 7. The D8112E, D8112E1, D8112G, D8112G1 and D8112A must have CS set to either Blank or a selection between 1 and 6 but not 7. Only Modem Format can report a 4 digit account number to the Central Station all others only report a 3 digit account number.

Creating a serial tunnel over the network to eliminate the need for long serial cables, or for connections to far for a serial cable to work.

How to interpret Alarm Recent Close reports from a 2000 series control panel. D2212,D2012,D2112,D2412,D2812

Issue How many zones is the D4112 Control Communicator capable of having?   Solution   The D4112 Control Communicator has six end-of-line resisitor supervised, hardwire protective zones. There are five standard programmable zones and one nominal 12 VDC powered zone optimized for two-wire smoke detectors

 How to enable Open/Close Reports for Part On Modes. The panel sends Open/Close reports for All-On but not for Part-On.

How to activate onboard relays from the panel keypad on 9000 – GV4 Series panels.

How to determine the value of Easy Series End of Line Resistors.

How to determine Popit Compatablity with the panel type. D9112B1, D9112, D9127T, D9127U, D9127, D8126T, D8126U, D8126, D8127T, D8127U, D8127