Security: Intrusion

How to determine the max distance of DS Multiplex module protected loop wire.

How to interpret the flashing green circle on the Easy Series control panel. Easy Series,IUI-EZ1

Issue How many on-board zones does the D6112 Control Communicator have?   Solution   The D6112 Control communicator has eight end-of-line resistor supervised hardwire protective zones. There are six standard programmable zones; one nominal 12 VDC powered zone optimized for two-wire smoke detectors and one nominal 12 VDC powered zone optimized for two-wire glass-break detectors.

How to interpret SERVC COMM FAIL displayed on Command Center. D7212B, D7212B1, D9112B, D1255

Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2

Issue What is the Bosch part number for the Inovonics FA206DS wireless motion detector?   Solution   The Bosch part number for the FA206DS would be the DS775RF and is used with the Inovonics FA400 receiver and the Bosch D8125INV wireless interface for Bosch D7412G/D9412G control panels.

How to correct the DS7400 Keypad beeping once every 10 seconds. DS7400Xi (Ver 3+),DS7400X,DS7400XIVER2,DS7400XIVER3+,DS7400XIVER4+

A possible solution to troubleshooting  a door opening when the # symbol is pressed.

Issue How many Skeds can be programmed with the D8112G2 Control communicator?   Solution   The D8112G2 can be programmed with up to 64 skeds.

Issue How is the battery test performed?   Solution   Type in (Command/ # ) 80 or a valid code # 80. If you want the sounder to trip with the battery test, type in #85. If the Green power LED contiunes to flash after 10 seconds, the battery has failed and needs to be charged or replaced. If the LED goes solid, the battery has passed.

How to correct the Panel reporting 'Service Phone Line' when programmed as Local.

Issue What voltage and current is the phone line monitor measuring to sense trouble on the phone line on the D7212B/D9112B panels?   Solution   The phone line monitor senses trouble when the voltage on the line falls below 4.5 to 7.5 VDC, or in the off-hook condition when the current is 8 to 13mA.

Issue What is the difference between the D9124 and the D9412G?   Solution   The D9124 is a D9412G with a 24 Vdc PSU and all the needed Fire Accessories for a basic system, all in one large red enclosure. See parts List below. The D9124 is made up of the following : D9412GLTB - Control Panel D9101 - Red Enclosure D9100 - Carriers Module with the Foolowing parts * * 2 - D192C - Bell Supervision Modules * 1 - D8125 - Popex Module * 1 - D928 - Dual Phoneline Switcher * 1 - D9142LC - 24Vdc Power Supply D1256 - Fire Keypad D1601 - Hardwire Transformer

How to learn the RF3502 into the panel; as a point or a keyfob assigned to a user? D4412, D6412, RF3224, RF3502

How to troubleshoot when the D6412 or D4412 panel will not release the phone line.

Issue How many 2 wire smokes will the D7112 support on zone 1?   Solution   Manufacturer & Models, and the number of smokes Radionics D262 with the D260 base  = 20 smokes DS200 with the MB200-2w base  = 10 smokes System Sensor 1400   =  10 smokes System Sensor 2400  = 10 smokes System Sensor 2400TH  = 10 smokes System Sensor 1451 with the B401 base  = 10 smokes System Sensor 1451 DH with the DH400 base  = 10 smokes System Sensor 2451 with the B401,B401B or DH400  = 10 smokes System Sensor 2451TH  with the B401,B401B or DH400  = 10 smokes System Sensor 2300T  = 10 smokes

Overview: Time needed to charge a 12 volt back up battery connected to a D4112 Issue   How long does it take to charge a back up battery connected to the panel for the first time?   Solution   It may take as long as 12 hours. BOSCH recommends that the battery be charged prior to the installation.

Issue Setting up the duress code on the DS7400XI 3+. Solution 1. Enter the program mode A. At the master keypad, enter the programmers code + #0. Ie...9876#0 Keypad should display: Prog.mode, the version and adr = 2. Enter a (2) digit report code in address 0322. Ie...032210#; this would be an example of a valid entry for the contact id mode. 3. Exit program mode A. At the keypad press and hold the star(*) key for 3 seconds and release it. You now should be out of the program mode, keypad should not display prog. mode anymore. 4. Assign the duress code to an available user #. A. At the keypad enter a master code followed by #0. Keypad now should scroll through an options menu. B. Press 0 then follow the instructions on the keypad. A duress code is authority level 5. Test the duress. The system should be armed and the exit delay time expired when disarming with the duress.

How to Capture and Save a DX4020-G Log file for troubleshooting