Can the D125B be Used to Power 2 Wire Smokes on the D7112?
Yes, see technogram number (73-06116-000-C) 1993 (attached). Listings and Approvals Underwriters Laboratories lists the D7112 ControVCommunicator as a Digital Alarm Communicator Transmitter (DACT) for: NFPA 71 Central Station, NFPA 72 Chapter 6 Local, NFPA 72 Chapter 8 Remote Station, NFPA 74 Household Fire Warning. The D7112 also has the following Approvals: CSFM and NYC-MEA (formerly NYC-BSA).
When I click on connect in RPS it brings up the standard connect window but the connect button is Greyed out and it will not allow me to call the panel.
RAMIV,RAMIV LITE,D5500C-USB,RPS,RPS LITE,D5500C-LPT
How long does a keypad message stay on the the keypad when it was sent from RPS or RAM IV Diagnostic Mode?
RPS,D7212,D7212B,D7212G,D7412,D9112,D9112B,D9412,RAMIV,D9412G,D7412G,D9112B1,D7212B1,D7412GV2,D7412GV3,D7412GV4,D7212GV2,D7212GV3,D7212GV4,D9412GV2,D9412GV3,D9412GV4
Overview
The Bosch Security Systems D221 Answering Machine Disconnect Module allows you to remotely disconnect an answering machine that shares a phone line with a Bosch Security Systems control panel. When the answering machine disconnects the phone line is available to the control/communicator for remote programming (RPS) functions. A Touch-tone® telephone at the RAM site is required to perform the disconnect procedure. The D221 can be installed with an existing modular telephone jack or be a replacement for an RJ-11 jack.
Issue
What activates the module to disconnect the answering machine?
Solution
From a touch tone phone call the phone line, let the answering machine answer the line. The # key or the 8 key will activate the module.
1) module white jumper cut = # key
2) module black jumper cut = 8 key
**Note: The RAM session is not affected when the D221 restores the phone line to the answering machine. Some answering machines record tones generated during the RAM session. If the D221 Module is used with an integrated telephone/ answering machine device, pressing the activation key ([#] or [8]) during normal use may activate the D221 and disconnect the device for 3 to 5 minutes.
How to program a shared area and sequence of operation of a shared area in conjunction with two associate areas.
D9412G,D7412G,D7212G,D7212,D7412,D9112,D9412G, D9412GV2,D9412GV3,D9412GV4,D7412GV2, D7412G, D7412GV3, D7412GV4, D7212G, D7212GV2,D7212GV3,D7212GV4
How to determine which points are available for programming using the D8125MUX.
D8125MUX, DS7457, DS7457I, DS7457IF, DS7460, DS7460I, DS7461I, DS7465, DS7465I, DS7052, DS7051, D7050, D7050-BB, MX835, MX934, MX794Z, MX250, MXB2W, D5060.
How do you enable basic Openings and Closing reporting by user on the 7000/9000 series panel?
D9412,D7412,D7212,D9412G,D7412G,D7212G,D9412GV2,D7412GV2,D7212GV2,D9412GV3,D7412GV3,D7212GV3,D9412GV4,D7412GV4,D7212GV4
How to configure the output in GV4 ver.2?
Default: 0
Selections: 0 to 8 (increments of 1)
Use this parameter to activate an output when the point goes into alarm.
The output does not activate for Trouble nor Supervisory events. Reset the output by clearing the memory from the keypad display.
The outputs used can be on an output module installed on either the Zonex bus or the SDI2 bus.
*Notice that the Relay will activate only when the point goes in to alarm, not when it changes to an off-normal state.
Follow the steps from this article to accomplish the BFSK relay functionality.
