Security: Intrusion

How to disarm All areas authorized by the user at once.

How to enable/disabling encoding tones on the D1254 Keypad used wth the D7112.

How to View the Event Log using the 540 command center with Honeywell 5800/5900 Series Panels. D540,5800B,5800B1,5900B1,5900B,5800C,5900C,5900G,5800G.

Issue On the Honeywell 520 keypad, NOT AUTHORIZED is being displayed when entering a code and CMD 48 to set up the next test time.   Solution   Only passcodes with authority level 5 (service level) are authorized to use CMD 42 and CMD 48 functions on the Honeywell 5505 using the 520 keypad.

Overview The Bosch Security Systems D221 Answering Machine Disconnect Module allows you to remotely disconnect an answering machine that shares a phone line with a Bosch Security Systems control panel. When the answering machine disconnects the phone line is available to the control/communicator for remote programming (RPS) functions. A Touch-tone® telephone at the RAM site is required to perform the disconnect procedure. The D221 can be installed with an existing modular telephone jack or be a replacement for an RJ-11 jack.   Issue   What activates the module to disconnect the answering machine?   Solution   From a touch tone phone call the phone line, let the answering machine answer the line. The # key or the 8 key will activate the module. 1) module white jumper cut = # key 2) module black jumper cut = 8 key **Note: The RAM session is not affected when the D221 restores the phone line to the answering machine. Some answering machines record tones generated during the RAM session. If the D221 Module is used with an integrated telephone/ answering machine device, pressing the activation key ([#] or [8]) during normal use may activate the D221 and disconnect the device for 3 to 5 minutes.

Issue Command 4 function on the 8112. Solution Reset Trouble Sounder Reset Alarm Memory Display Display Clock COMMAND 4 performs several functions for your securitysystem. Use this command to silence your Alpha II steady troubletone during system trouble events or clear the alarm memory displayof the Alpha II Command Center. Your security system may be programmed with an internalclock. To display the clock momentarily at the Alpha II CommandCenter, enter COMMAND 4. The display will showTEST= (time display) . If the display showsTEST= without the time display, then yoursystem is not programmed for clock displays. All other functionsof COMMAND 4 are still available. To use COMMAND 4: Ensure that your security system is disarmed. Press the COMMAND bar. The display should show SYSTEM COMMAND Press the 4 key. The display should showTEST= (time display) momentarily. If the displayshows TEST= , with no time display,your system is not programmed to indicate time of day.However, resetting the trouble sounder and clearing the alarmmemory display still remain functional. Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2

Issue How to arm entire system with delays.   Solution   To arm the entire system with delays, follow the steps below: COMMAND 1 is used to arm the entire system, both perimeter and interior zones. Once you have entered COMMAND 1, the exit delay time starts. You now have a predetermined amount of time to exit the protected area before the system arms. During the exit period, you may move through motion detectors or any protected area on your way to the exit door without causing an alarm. To cancel COMMAND 1, enter your personal passcode and press ENT. NOTE: If you leave the building after the exit time expires, you may begin the entry delay, or initiate an alarm. If this happens, disarm your system by entering your personal passcode and press ENT . If your system reports to a Central Station, you may need to call them if an alarm occurs. Application COMMAND 1 is useful in applications where you want your cleaning service, a serviceperson or anyone to arm your system when they leave, but you do not want them to have the passcode to disarm the system. COMMAND 1 arms the system, but it will not disarm the system. Arming with COMMAND 1: 1. Ensure that all zones are secure. All of the Zone Status indicator lights on the Command Center should be off. 2. Press the COMMAND bar. The Command Mode indicator light comes on. 3. Press the 1 key. The PERIMETER indicator and the INTERIOR indicator lights begin to flash on and off. This indicates that the system has begun exit delay time. 4. To disarm your security system or cancel COMMAND 1, enter your personal passcode and press ENT before the delay time expires.

How to Activate the ALT ALARM RELAY on a D8112 Panel. When is the ALT ALARM RELAY triggered? D8112G2,D8112E1,D8112G1,D8112A

Issue Does the panel need to see a perimeter point faulted during the exit delay when arming All On to actually fully arm the system and not just Part Arm?   Solution   When the ARMING OPTIONS prompt Enable 'All On - No Exit ' feature is set to yes , the panel must see a perimeter point faulted during the exit delay in order to fully arm . If the panel does not see that , the panel will switch to PART ON to prevent a false alarm.

How to interpret the Alert Light flashing the DS7100 panel keypad after disarming. DS7140,DS7100.

How to determine how many keypads are supported on the DS7060 and allowed wire distance. DS7060,DS7447,DS7445,DS7443

How to properly turn off a point in the D6112 or D4112. Why is the D6112 point showing faulted even when using a point code of 00000?

How to determine compatibility with iPhone or Android application using a Cellular Network. What is required of the GV4 series panel in order to use the iPhone or Android application over a cellular network? B450, B440, B441, B442, B443

How to interpret the keypad display: SERVC 9210.