Security: Intrusion

Issue This is a report that is generated when the system is armed and Closing Ring Back is enabled but the closing report is not. The Report 0 occurs because the panel does a phone check to see if dial-tone  is detected. If dial tone is not detected at the time the panel is armed it will display a Communication Fault on the Keypad it will generate this error in the History buffer. How are Report Fail 0 messages prevented? Solution To prevent these errors from occurring perform the following steps: On the DS7400/X version 1.xx 1. Enter in program mode by entering in the program PIN + #0 2. Depress 0011 03# 3. Hold the * key for 3 seconds to exit out of Program mode  On the DS7400Xi  Version 2.xx and Ver 3+ 1. Enter in program mode by entering in the program PIN + #0 2. Press 0000 03# 3. Hold the * key for 3 seconds to exit out of Program mode On the DS7400Xi Ver 4 1. Enter in program mode by entering in the program PIN + #0 2. Press 0000 03# 3. Hold the * key for 3 seconds to exit out of Program mode Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+,

How to correct when the keypad will not arm but displays Change of Relay. D1255,D1260,D7212GV2,D7412,D7412GV2,D7412G,D9412G,D9412GV2

Issue If using the D220A on the D2112 do I have the Exit Feature? Solution No, the D2112 does not have the Exit Feature. It uses the "Step Out Feature". The Exit Feature does appear on page 23 of the Users Guide, but that is because this Keypad can also be used on other 2000 Series Panels which have the Exit Feature.

  Issue The D192G panel zone (point) is in trouble and the yellow LED is not on. Solution With the zone/point in trouble and No Yellow LED On there is a wiring fault. One of the following terminals do not have power connected to them. External Power In (EXT PWR IN) Auxiliary Power In (AUX PWR IN) Terminal 1 (AUX PWR IN) 13.75 VDC Terminal 2 (Common) Terminal 3 (Supervised Zone / Point) 2.50 VDC Normal Condiction < 1.50 VDC In Trouble Condiction Terminal 4 (Trigger) 13.75 VDC  In Alarm Only Terminal 5 (External Power In) 12 VDC or 24 VDC Depended on needed Output for the NAC's or Power Supply Terminal 6 (Common) This is the Common from an 24 VDC External Power Terminal 7 (Positive Alarm Output) Terminal 8 (Negative Alarm Output)

How to make the D127 D127 Reversing Relay activate on alarm. The D127 does not activate when I trip the alarm.

Issue Panel history shows a failure 3.   Solution   If panel is programmed to do a history dump to WDSRP but failed to communicate via the phone line that is programmed for remote callback, the panel will initiate a failure 3 trouble.   Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+,

Part numbers D2212, D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U D2812P

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, DS7460, DS7465,DS7445, DS7432, DS7457i,DS7460i, DS7461i, DS7465i, D8125MUX, D5060, D7412G, D9412G, D7412GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G, B600

How to enable phone line supervision in the D4412 or D6412.

How to disable reporting in the DS7090 or DS7090i. DS7090,DS7090I,DS7090TM,DS7090TMI

D7212, D7412, D9112, D9124, D9412, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3

Issue How is the panel made local so it will not send anything to the Central Station? Solution Receive a copy of the program with the D5200 programmer and follow the steps below. Enter “AUX” Enter “LOGGER” Select "NO" for all line items Load record back into panel and it will no longer send to the Central Station.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3,

 Issue Is there a list of commands for the DS panels?   Solution   DS Commands DS7090, DS7090I, and DS7100 Command 1            Arm All Command 2            Instant Arm Command 3            Delay Arm Command 4            Custom Arm Command 5            Custom Arm Command 6            Custom Arm Command 7            Alert Mode (chime mode) Command 9            Zone Bypassing Command 81          Area Test Command 89          History Command 89*        History Reset Command 80          Battery Test Command 82          Communicator Test Command 80          Fire Reset Command 84          Indicator Light and Display Test Command 83          Remote Program Dial Out Command 86          Remote Program Answer Command 85          Siren Test Command 87          Trouble Display Command 87*       Trouble Display Reset

Issue What are the SDI addresses on the D6412 and D4412?   Solution   SDI Address             Device Description 0 =           Installer Keypad, or local connection to RAM IV                         1-8 =          Command Center 1 to 8 40,41 =       DX8010 Telephone Control Module 50,51 =       RF Receivers 1, and 2 52-55 =      RF Keypads on RF Receiver 1 60-63 =       RF Keypads on RF Receiver 2 101-107 =   DX 2010 wired point expander 150-151 =   DX 3010 Octo-Output expander 250 =           DX4010 Serial RS-232 Interface module

Issue What is the open air range on the 2 button and 4 button ITI keyfobs?   Solution   The 60-607-319.5 two button and the 60-606-319.5 four button ITI keyfobs are 500 feet open air transmitters.