About Central_Support

Motion detection is an important option in most surveillance systems. Depending on your configuration, you can determine when video is recorded (saved on the surveillance system server), when notifications are sent, when output is triggered and more. Follow the steps below if you want configure your camera to detect motion and then send the event to the server, to start recording. This guide helps you set this option only for nights and weekends. It is important that you find the best possible motion detection settings for the camera in order to avoid unnecessary recordings or notifications. Article requirements: Configuration Client PC/ Server/ Workstation Camera Step-by-step guide A) Configuring MOTION+: Open Configuration Client > Devices tab > Expand VRM Devices   Select your camera with VCA functionality under the Pool:   Select VCA tab > Make the configuration as in the following picture and set the Aggregation time [ s ] you desire. This option prevents multiple alarms from triggering during the defined time > Save your changes    B) Adding camera to the logical Tree: Go to the Maps and Structure tab > select your camera under the Pool > Drag and drop it into the Logical Tree (on the right side) > Save your changes       C) Activating motion alarm and recording Go to the Cameras and Recording tab >Select VRM> Note the Device Family name > press on the Edit scheduled recording settings button   Create new schedule and rename it > On the "Day" tab: tick the "Off" option near Recording   Go to the Night tab and tick "On" option near Recording. Change options as in the picture below > Ativate Motion Alarm > set the desired duration time for Pre-alarm and Post-alarm Repeat the same steps for the Weekend tab and click OK   Assign the recording schedule to the camera > Save the changes. You have configured the motion recording.   ... View more

Question To ensure the highest customer satisfaction and replace the defective hardware faster and more smoothly, it is necessary to register each system for the specific country together with the system location. But where and why should you register your device? Answer The next business day on-site service level and the parts replacement within 3 business days can only be provided if the respective system has been registered immediately after receipt and installation. Otherwise, service will be provided based on best effort basis. If you own one of the products below, we recommend that you register your device immediately: DSA E-Series (E2700 & E2800) DIVAR IP all-in-one 4000 DIVAR IP all-in-one 5000 DIVAR IP all-in-one 6000 DIVAR IP all-in-one 7000 (DIP-72xx, DIP73xx, DIP-74xx) DIVAR IP 6000 rev. 2 (DIP-61xx) DIVAR IP 7000 rev. 2 (DIP-71xx) HP Enterprise server products HP workstation products    Easy and fast, you can register each product by completing the form online here Select your device from "Product Family" drop-down list Fill in the commercial type number and the serial number of the device Complete all required information about the site where your device was installed Fill in all the correct contact details of the engineer responsible for the system   Good to know: You can register multiple units through a single registration form. This might be possible only if the Physical Address of all your units is the same. Fill in the Serial Numbers (SNs) of the units with ";" between them,  rather than wasting time and filling out different registration forms for each one. Note: Some fields are mandatory and are marked with * and each field has a note in order to help you complete your registration form correctly.   Central Support Team will handle your request in the shortest time. ... View more

This Article describes how to upgrade to the latest Image Version on a DIVAR IP 6000/7000 R2 via USB Boot Medium The latest suitable Image for your DIVAR IP R2 Family Device can be obtained from Bosch Central Technical Support Team. Please provide the SN (serial number) from the DIVAR IP 6000/7000 R2 when contacting Bosch Central Technical Support Team.   Step-by-step guide 1. Create the USB Boot medium For this you need the ISO Image and an USB Medium Creator Tool like Rufus (https://rufus.ie) Create the USB Boot Medium like shown in the Picture (this can take up to 15 minutes) 2. Plug-in the USB to the DIVAR IP and start/ restart the Unit While starting, press F11 to go into the Boot device selection Screen From there select the USB Stick as boot device In the System Management Utility Screen select Option 2 System Recovery to update the OS 3. After this process restart the DIVAR IP, unplug the USB and start Windows normally The DIVAR IP might restart once due to first installation process Note: Please make sure you are NOT using Option 1 Initial Factory Default, because then you loose all the Data on the Storage Please note that the OS will be reinstalled from the Image, you might need to install Windows updates and other Software again ... View more

Question Perhaps you are here because you encounter a message like the one below and you cannot access your DIVAR IP 7000 R2 under proper conditions. "The instruction at 0x6566f31c referenced memory at 0x00000008. The memory could not be read." But what might be the cause?   Note: Please note that this example is related to the following system: DIVAR IP 7000 R2 ATI Firepro graphics processing unit (GPU)   Answer The message relates to NVIDIA drivers. A possible workaround could be to login as BVRAdmin and delete all NVIDIA related drivers and software from the unit. You should go to Control Panel > Add/ remove software and remove all NVIDIA related   Important: Please make sure that you have not upgraded the Image to 1.03 as this is a older DIP 7000 R2 with an ATI Firepro GPU instead of NVIDIA GPU. If so, check the following article, where you will find useful information about the DIVAR IP 7000R2 and DIVAR IP 6000R2 ISO image for recovery. ... View more

Stay up to date with all recommendations, guides, tips and tricks shared by experts on the Bosch Building Technologies Knowledge Base ! RSS (Really Simple Syndication) feed is a data format used for providing users with frequently updated content. Through the RSS option, you have constant news sources at your disposal, without having to spend time searching for them. It constantly monitors the site and informs you through an e-mail of any new articles published on the Knowledge Base.   This step-by-step guide shows you how to add the RSS feed to your Outlook email inbox. Step-by-step guide   In the following example you will find how to add RSS feed for VIDEO security category: Open Outlook and search for the RSS Feed folder > Right click on it >Click on "Add a New RSS Feed..." In Office 365, the folder name was changed: RSS Subscriptions Copy the following link in the new window that opens and click the Add button: https://community.boschsecurity.com/varuj77995/rss/board?board.id=bt_community-tkb-video Organize your Outlook mailbox and add the Security: Video articles folder to Favorites Here is the User interface of the feed reader:   Good to know: You can add RSS feed links for the other Security categories from Bosch Building Technologies Knowledge Base ! If you are interested in Intrusion, Access Control, Fire, Public Address , Conference and Discussion systems, follow the same steps as above, but change the link with the one that suits your interests. Security: Video https://community.boschsecurity.com/varuj77995/rss/board?board.id=bt_community-tkb-video Security: Intrusion https://community.boschsecurity.com/varuj77995/rss/board?board.id=bt_community-tkb-intrusion Security: Access Control https://community.boschsecurity.com/varuj77995/rss/board?board.id=bt_community-tkb-accesscontrol Fire https://community.boschsecurity.com/varuj77995/rss/board?board.id=bt_community-tkb-fire Installed Audio: Public Address https://community.boschsecurity.com/varuj77995/rss/board?board.id=bt_community-tkb-audiopublic Conference & Discussion https://community.boschsecurity.com/varuj77995/rss/board?board.id=bt_community-tkb-conference ... View more