Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 
    Sort by:
    ‎12-07-2021 09:17 AM
    This is how to troubleshoot where turning the key to the Test position does not put the smoke detector inside the duct enclosure into alarm, which will likely be due to the coil is missing.
    View full article
    ‎05-02-2023 10:43 AM
    This article describes how to capture the panel/ controller communication log when requested by Technical support.
    View full article
    ‎10-20-2022 01:58 PM
    This article explain how it is possible to automatically zoom in the map in case of alarm.
    View full article
    ‎06-15-2022 04:16 PM
    Follow the steps from this article to access the Point Description programming.
    View full article
    ‎09-07-2022 05:00 PM
    Follow this step-by-step guide and learn how you can use keypad programming to configure FPD-7024 IP communications
    View full article
    ‎07-07-2022 04:02 PM
    Follow this step-by-step guide from this article and find out how to stop and restart the FSM Server service
    View full article
    ‎06-02-2022 10:48 AM
    Part numbers FPA-1000, FPA-1000UL, FPA-1000-V2
    View full article
    ‎10-18-2022 03:41 PM
    To silence all NAC's of one panel (FPA-5000/Avenar) from the map in FSM Step-by-step guide   Insert a sensor on the map of FSM Under sensor properties choose: General: Add symbol: FIRE_Panel_FPA_BG Settings: Driver Instance: the panel / compound where the FSM is belongs to Address-> e.g. Panel 1-10.1 ! Please pay attention: there are other “Panel” possibilities to choose. Please do not choose Panel 1-10 (Communication)! After inserting the settings click “ok” Then Apply At the map when you right click the panel symbol you will get the commands as shown below.   If there is a fire alarm, you can right click at the panel and then click at “silence on”. Please be sure, that then every NAC which is belonging to this panel is “silenced”. Additional: there is also a command "silence scope" which then has the effect, that the whole scope will be silenced.
    View full article
    ‎10-18-2022 03:52 PM
    Library is offering 3 different sizes of detectors and can be customized. See this article and find out how you can customize Symbols (icons) - FSM
    View full article
    ‎10-19-2022 03:52 PM
    This article explains step by step how to enable commands for operator (other than admin) in FSM
    View full article
    ‎07-07-2022 04:07 PM
    Follow the steps from this article to see the labels from the sensors in FSM which are configured in RPS
    View full article
    ‎11-11-2022 11:59 AM
    This article is a step by step guide about how to create panel container on map by using Macro-Area (point) on FMS.
    View full article
    ‎10-18-2022 04:16 PM
    Have a look at this article and see how you can setup the FMS - OSD Logo
    View full article
    100% helpful (1/1)
    ‎01-19-2024 01:17 PM
    The following steps describe an efficient way to update the panel firmware in an AVENAR panel 4.x network via SD card, thus keeping downtime of the panels to a minimum. To further reduce downtime, it is recommended to network the panel nodes via ETH.
    View full article
    ‎10-18-2022 04:05 PM
    Follow this article and learn about the option which allows you to configure the color for each state & sensor in FSM
    View full article
    ‎10-18-2022 03:26 PM
    Live time event printing is supported. To enable it, add a xml file in program data folder with the name of the printer.
    View full article
    ‎10-25-2021 01:14 PM
    Learn from this article how to enable usage type Fire on KD55 element from Bosch Remote Programming Software (RPS)
    View full article
    ‎04-02-2021 05:25 PM
    This feature blocks the programming feature through the keypad of the FPD-7024. This feature is only enabled via RPS.   Step-by-step guide   1 Connect to the Panel via RPS an Open the FPD-7024 programming sheet.   2 Go into Program Accounts and Remote Access Security.   3 Open Anti-takeover Setting and Select "Lock all local programming (except Date/Time and all user PINs)" to block the programming via keypad of the panel.  
    View full article
    ‎10-18-2022 02:47 PM
    This article explain what should be done if new detectors are added to the system. 
    View full article
    ‎08-04-2022 02:58 PM
    This article contains a step-by-step guide about how you can set the field of view (FoV) of AVIOTEC IP starlight 8000
    View full article
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist