Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 
    Sort by:
    ‎05-19-2022 09:10 AM
    Can the installer code be returned to default in the FPD-7024, D7024, DS9400, DS9400I, DS9400M fire panels?  
    View full article
    ‎06-06-2022 09:50 PM
    How to configure the FPD-7024 to communicate by phone using keypad programming. How to use keypad programming to configure the FPD-7024 for phone communications.
    View full article
    4 weeks ago
    How to use the DX4010V2 for connecting to the FPD-7024 with RPS. How to correct the FPD-7024 indicating Trouble Missing DX4020 or DX4010V2.  
    View full article
    ‎05-17-2022 09:53 AM
    How to upgrade the FPA-1000 from Version 1 to Version 2.
    View full article
    ‎05-16-2022 09:16 AM
    Part numbers FPD-7024, B426, B420, DX4020, B450, B440, B441, B442, B443, B444
    View full article
    ‎05-02-2023 10:08 AM
    Panel controller displays can become de-calibrated, e.g. upon initial power-up followed by unintentional contact with the display or inaccurately touching the crosshairs.  It becomes noticeable after the panel controller has re-booted and does not respond properly to touch.
    View full article
    ‎05-19-2022 09:25 AM
    FPA-1000, FPA-1000UL, FPA-1000V2, FMR-1000-RCMD, FRM-1000-RA
    View full article
    ‎10-31-2023 09:36 AM
    This article provides instructions for troubleshooting Ground Fault in the FPD-7024 or D7024
    View full article
    ‎06-15-2022 06:36 PM
    Follow the steps from this article to configure FPD-7024 to communicate using Cellular or Ethernet network communications. How to configure the FPD-7024 for network communications using keypad programming.
    View full article
    ‎04-14-2022 05:08 PM
    This article explains how you can reset the FPA-1000, FPA-1000-UL, and FPA-1000-V2 panels.
    View full article
    ‎03-29-2022 04:42 PM
    When using Wheelock / Cooper / Eaton Exceeder LED 3 Strobes and Horn Strobes on a UL Listed Bosch Fire panel a DSM or SM Wheelock Sync Module is required.
    View full article
    ‎02-16-2022 09:47 AM
    This guide gives a example of how to check that OPC is receiving commands and transmitting to controller.
    View full article
    ‎05-20-2022 02:28 PM
    Part numbers DS240, DS241, D296, D297
    View full article
    ‎02-18-2022 04:02 PM
    In cases where RPS configuration cannot be loaded please follow the instructions from this article.
    View full article
    ‎07-07-2022 03:38 PM
    Is always recommended to backup the database before running the default process. Find out in this article the steps to restore default FSM (Fire Monitoring System) configuration
    View full article
    ‎10-18-2021 01:01 PM
    Use the tool provided when FSM server application is installed, to manage export/import of configurations. Please note: This tool is only for configuration backup and does not include logs and history.
    View full article
    ‎09-14-2021 09:49 AM
    A sticker on the front of the B450 indicates proper switch positions for selecting various SDI or Option Bus addresses (see figure 1). Figure 1 Sticker with address configurations   There are 2 types of FPD-7024 panels. It must first be determined which is in use before selecting the B450 address: Newer types with firmware version 1.06 and higher. These types are identified by icons on the keypad instead of words (see figure 2). Older types with firmware version 1.03 and lower. These types are identified by words on the keypad. Figure 2 Version 1.06 with Icons vs 1.03 with words   Version 1.06 & newer types: When used as sole communicator or backup to phone line, set the address wheel at 9 for Option Bus address 250. When used as backup to a primary network communicator, set the address wheel at 6 for Option Bus address 134. RPS connections require Option Bus address 250. Be sure the address wheel is set at 9 on the network communicator intended for RPS connections (Ethernet is preferred when allowed). Version 1.03 and older types: Use Option Bus address 250. Only one network communicator is available on these panel types.
    View full article
    ‎06-02-2022 10:53 AM
    Part numbers D7052, D7024, FPD-7024, DS9400, DS9400I, DS9400M, MX363
    View full article
    ‎05-02-2023 10:43 AM
    This article describes how to capture the panel/ controller communication log when requested by Technical support.
    View full article
    ‎05-02-2022 03:07 PM
    If FSM needs to be connected to a new panel (network), then proceed as it is described in this article:
    View full article
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist