Security: Intrusion

Part numbers D192C, D192G, D2212, D2212E, D2212BE, D2412, D2812

Issue Can I mix Heat Detectors and 2 wire smokes with a sounder when using a D132A Smoke Detector Polarity Reversing Module? Solution No. When a Heat detector goes into alarm it puts a short on the input zone to indicate the alarm. The D132A uses Aux power from the panel when the polarity reversal takes place and since a heat detector does not reset when polarity is reversed, it would put a direct short on the Aux power of the panel. Consequently everything connected to the same Aux power terminals would not function.

Issue What is the difference between the D133 an D134? Solution The D133 has a single relay rated at 2A @ 30 VDC – 0.6A @ 125 VAC. The D134 has two relays rated at 2A @ 30 VDC – 0.6A @ 125 VAC. Current draw for the Relay is 40 mA per relay when activated.

Issue Will an Answering Machine cause the D168A not to answer when accessed locally? Solution Some answering machines load down the phone line and cause it to go below 7 VDC. The D168A needs at least 7 VDC to properly process the DTMF tones.

How to correct the D132A supervision point not showing normal circuit status.  Cannot get the onboard point from the D132A module to show normal circuit status. D132A,D4412,D6412,DS7220,DS7240,D2212

How to configure the 2000 Series to use 4-Wire smokes. D2212,D2412,D2812 D133, D134

Part numbers D222A, D223A, D222AW, D223AW

Issue Can zones 7 and 8 be used as normally open zones, and do they require any supervision?   Solution   Zones 7and 8 are not supervised on the D2112 and D2212 panels and therefore can only be used as normally closed zones, they will not work as normally open zones because no EOL is used. Voltages of 2.4 to 13.9VDC would be an open condition while voltages 0.0 to 1.4VDC would indicate a closed circuit on these points.

Part numbers D2212, D2412, D2812

Part Numbers D2212, D2412, D2812, D222, D222A, D223, D223A

How to prevent Users from Changing Codes on 2000 Series panels. Pressing 5 to change codes is available to Owners and Users. How can Users be prevented from changing codes? D2212,D2412,D2812

How to program RF Points into 2000 Series control panels. D2212, D2412U, D2812

How to locate the Program Entry Guide for D2412 or D2812 panel types. D2412U, D2412UE, and D2812

How to lock access to the panel program to prevent take overs. D9112B1, D2012, D2112, D2212, D2412, D2812, D7212B, D7212B1, D8112G2L, D9112, D9112B, D9112B1

How to connect 4-wire Smoke Detectors to D2000 Series Control Panels. D2212B, D2212BE, D2412U, D2412UE, D2812

How to prevent regular Users from Changing codes on 2000 series control panels. D2212, D2412, D2812, D2012, D2112, 2000 Series

Issue What handler is used to program the D2812 panel. Solution The D5200 2212 product handler supports the following panels: D2212, D2212B, D2212BE, D2412, D2412U, D2812, D2812U.

How to operate the 2000 series control panel. How to use system test mode, check system troubles, work with passcodes, change watch tone and arm.

How to connect to RPS with the modem connected directly to the Panel. How can I connect to a panel with a modem and only 1 phone line?