Security: Intrusion

  How to determine the zone code used on a 2000 Series panel for a D132A trouble point. D132A,D2412,D2812,D2212  

How to program a duress code that operates normally but sends duress to a receiver.

How to correct the inability to view troubles by pressing the 4-key on 2000 series panels.

How to correct the Duplicate Point display when adding points into RF programming. D2412,D2812,D2212,D208RF,D216RF  

How to correct the 2000 series does not allow passcode changes by pressing the 5 key.

Issue What revision D2212 panel was compatible the the D169?   Solution   Revisions 2.53 and later panels are compatible with the D169 2-way voice.

Issue What keypads are compatible with the D2412?   Solution   The D202A, D205, D206, D220A, D222, and D223 keypads are compatible.

Issue How can I setup Open/Close on a 2000 series panel?   Solution   Using RPS/RAMIV 1. Connect to the control via modem/RPS and receive all panel data and save to your RPS database. 2.  Go to the Reports section of the program. A. Turn on All-On reports by selecting Yes. B. Turn on Part-On reports by selecting Yes. 3. Save your changes and send the changed data back to the control. Test it out. Using 5200 1. Latch the installer clip on the control panel and receive a fresh copy of the panel data. 2. After you see Receive Successful on your 5200, go to the Reports section of the program.  3. Using the white SPACE bar on the 5200 press it to toggle NO to YES to turn on O/C for both ALL ON and PART ON. 4. Press the red SEND LOAD key, disconnect the programmer and unclip the installer switch. Test it out.

How to correct erratic operation of the GE-ITI 60-641 Long Life Door/Window Sensor. 60-641-95 Long-Life D/W Sensor Gray, 60-641-11-95 Long-Life D/W Sensor Brown, D216RF, D208RF, D2412, D4412, D6412, D2212, RF3226, D2812

How to troubleshoot the 2000 series panel when the keypad reads Call For Service. My D2212 reads "Call For Service" and does not show anything else.  How do I determine the issue? D2212, D2412, D2812

Part numbers D2212, D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U, D2812P, D222A, D223A, D202A, D220A

Part numbers D2212, D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U, D2812P, D208RF, D216RF, RF3226

Part numbers D2212, D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U, D2812P,

Part numbers D2212, D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U, D2812P, D222A, D223A, 

Part numbers D2212, D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U, D2812P, D222A, D223A, D202A, D220A

How to initiate a programmed test time on 2000 Series control panels.  Does the D2212 Timer Test Need to be Initiated from the Keypad? D2812,D220A (8 led),D2412,D2212,D222A LCD,D223A LCD,D220A,D222,D223

Part numbers D2212, D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U, D2812P

Overview New RF Receiver Trouble, Receiver ‘Jammed’ When used with RF Receivers with firmware 9.0 (or later), D2212Bs with revision 3.03 firmware (or later) can display two distinct trouble conditions. The receiver trouble display is expanded to two lines. Issue RCVR # TROUBLE 2111 # is the receiver number (7 or 8). RCVR # TROUBLE 1211 # is the receiver number (7 or 8). Solution 2111 in the second line indicates that no sensor has been heard from in a calculated interval. The interval depends on the number of sensors in the system. 1211 in the second line indicates that the receiver is in a ‘jammed’ condition. Interference is at a level that prevents sensor transmissions from being received.

Issue   Trouble tones will clear and then return one hour later.   Solution   RF Sensor Low Battery With earlier revisions of panel firmware, users could silence a low RF fire sensor battery trouble indefinitely. With revision 3.03 (or later), the panel restarts the trouble sounder at the keypad within four hours if the low battery in the fire sensor is not replaced.

Overview Remote Program (Key 2) After pressing the [2] key and entering an Owner passcode to enter the Remote Program Mode, the display shows SYSTEM PROGRAM IN PROGRESS. If the [CLEAR] key is pressed to return to the OFF state, the system will not allow re-entering the Remote Program Mode for 30 seconds. Issue Remote Program (Key 2) and owners code will not work twice in a row. Solution D2212B Firmware Revision 3.03 After pressing the [2] key and entering an Owner passcode to enter the Remote Program Mode, the display shows SYSTEM PROGRAM IN PROGRESS. If the [CLEAR] key is pressed to return to the OFF state, the system will not allow re-entering the Remote Program Mode for 30 seconds.