Bosch Building Technologies

    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Intrusion

    Sort by:
    ‎06-15-2018 03:27 PM
    Issue What is the difference between the D133 an D134? Solution The D133 has a single relay rated at 2A @ 30 VDC – 0.6A @ 125 VAC. The D134 has two relays rated at 2A @ 30 VDC – 0.6A @ 125 VAC. Current draw for the Relay is 40 mA per relay when activated.
    View full article
    ‎06-15-2018 02:41 PM
    Issue Will an Answering Machine cause the D168A not to answer when accessed locally? Solution Some answering machines load down the phone line and cause it to go below 7 VDC. The D168A needs at least 7 VDC to properly process the DTMF tones.
    View full article
    ‎06-15-2018 02:13 PM
    How to correct the D132A supervision point not showing normal circuit status.  Cannot get the onboard point from the D132A module to show normal circuit status. D132A,D4412,D6412,DS7220,DS7240,D2212
    View full article
    ‎06-15-2018 02:07 PM
    How to configure the 2000 Series to use 4-Wire smokes. D2212,D2412,D2812 D133, D134
    View full article
    ‎06-14-2018 07:23 PM
    Part numbers D222A, D223A, D222AW, D223AW
    View full article
    ‎06-14-2018 07:09 PM
    Issue Can zones 7 and 8 be used as normally open zones, and do they require any supervision?   Solution   Zones 7and 8 are not supervised on the D2112 and D2212 panels and therefore can only be used as normally closed zones, they will not work as normally open zones because no EOL is used. Voltages of 2.4 to 13.9VDC would be an open condition while voltages 0.0 to 1.4VDC would indicate a closed circuit on these points.
    View full article
    ‎06-14-2018 03:56 PM
    Part numbers D2212, D2412, D2812
    View full article
    ‎06-14-2018 03:43 PM
    Part Numbers D2212, D2412, D2812, D222, D222A, D223, D223A
    View full article
    ‎06-13-2018 04:01 PM
    How to select watch tone on a 2000 Series Panel. D2212,D2012,D2112,D2412,D2812,D222A LCD,D223A LCD,D202A,D220A
    View full article
    ‎06-12-2018 10:36 PM
    How to prevent Users from Changing Codes on 2000 Series panels. Pressing 5 to change codes is available to Owners and Users. How can Users be prevented from changing codes? D2212,D2412,D2812
    View full article
    ‎06-08-2018 10:01 PM
    How to program RF Points into 2000 Series control panels. D2212, D2412U, D2812
    View full article
    ‎06-08-2018 08:54 PM
    How to locate the Program Entry Guide for D2412 or D2812 panel types. D2412U, D2412UE, and D2812
    View full article
    ‎06-08-2018 08:00 PM
    How to lock access to the panel program to prevent take overs. D9112B1, D2012, D2112, D2212, D2412, D2812, D7212B, D7212B1, D8112G2L, D9112, D9112B, D9112B1
    View full article
    ‎06-08-2018 03:51 PM
    How to connect 4-wire Smoke Detectors to D2000 Series Control Panels. D2212B, D2212BE, D2412U, D2412UE, D2812
    View full article
    ‎06-08-2018 03:28 PM
    How to prevent regular Users from Changing codes on 2000 series control panels. D2212, D2412, D2812, D2012, D2112, 2000 Series
    View full article
    ‎07-11-2018 05:09 PM
    Issue What handler is used to program the D2812 panel. Solution The D5200 2212 product handler supports the following panels: D2212, D2212B, D2212BE, D2412, D2412U, D2812, D2812U.
    View full article
    ‎06-01-2018 10:13 PM
    How to operate the 2000 series control panel. How to use system test mode, check system troubles, work with passcodes, change watch tone and arm.
    View full article
    ‎05-31-2018 10:42 PM
    How to connect to RPS with the modem connected directly to the Panel. How can I connect to a panel with a modem and only 1 phone line?
    View full article
    100% helpful (1/1)
    ‎06-14-2018 07:57 PM
    How to troubleshoot the message "Keypad Disabled" on the D222 or D223 keypad.
    View full article
    ‎05-25-2018 08:29 PM
    Could not connect to 2212 panel, programmer would say " FAIL PROD ID D5200,D2212
    View full article
    Top Contributors