Security: Intrusion

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3,D7412GV3, D9412GV3, D7212GV4, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G, D2212, D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U, D2812P, D6412, D4412, B3512, B4512, B5512, B6512

How to correct the unresponsive D8112 panel keypad with a Constant Buzz. 5505,D8112A,D8112E1,D8112G1,D8112G2

  Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2, D192A, D192C

Part numbers D8112, D8112E, D8112E1, D8112G, D8112G1, D8112G2

Issue What are the enviromental considerations for the proper operation of the Bosch control/communicators? Solution Indoor Dry.   Relative Humidity 5% to 85% noncondensing at +86 degrees Fahrenheit (+30 degrees Celsius). Operating temperature would be +32 degrees Fahrenheit to +120 degrees Fahrenheit ( 0 degrees Celsius to 49 degrees Celsius ).

Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2

D5200 Programmer:  The D5200 needs to match a Data Lock code in the panel to access programming. Changing the panel Data Lock Code from the default of 12345 will prevent access. Remote Programming Software: RPS also needs to match the Data Lock code in the panel to access programming.  Changing the panel Data Lock Code from the default of 12345 will prevent access. RPS also needs to match the RPS Passcode (or RAM Passcode in legacy types) in order to allow access programming. Changing the default from 999999 will block RPS access.

How to troubleshoot sending or receiving D8112 programming with the D5200.

Issue The D8112 panel is not sending signals when modem format is selected to the Central Station. Solution Only the D8112G2 can send signals in Modem II format with a CS setting of 7. The D8112E, D8112E1, D8112G, D8112G1 and D8112A must have CS set to either Blank or a selection between 1 and 6 but not 7. Only Modem Format can report a 4 digit account number to the Central Station all others only report a 3 digit account number.

Issue How many zones can be programmed on the D8112G2?   Solution   The D8112G2 is capable to have 8 master zones that may be expanded to 134 individual zones of protection.

Issue   How many codes can be programmed for the D8112G2?   Solution   The D8112G2 can be programmed with up to 70 individual combinations.

Part numbers D8112, D8112E, D8112E1, D8112G, D8112G1, D8112G2, D1252, D1252A, D8129

Issue How many Logger Events can the D8112G2 store?   Solution   The D8112G2 Control Communicator can store up to 400 Events in the panel memory. The panel logs the time, date, event, master zone, and the primary or alternate phone number called for each event. The 400 events can be retrieved with the RAM II, RAM IV or RPS downloading software.

How to program a zone to activate Alternate Alarm. D8112G2,D8112E1,D8112G1,D8112A.

Issue Arming an 8112 with delays.   Solution   COMMAND 1 is used to arm the entire system, bothperimeter and interior zones. Once you have entered COMMAND1, the exit delay time starts. You now have a predeterminedamount of time to exit the protected area before the system arms. During the exit period you may move through motion detectorsor any protected area on your way to the exit door without causingan alarm. Enter your personal passcode to cancel COMMAND1. NOTE: If you leave the building after the exit time expires,you may begin the entry delay, or initiate an alarm. If this happens,disarm your system by entering your personal passcode. If yoursystem reports to a Central Station, you may need to call themif an alarm occurs. COMMAND 1 is useful in applications where you want yourcleaning service, a serviceman or anyone to arm your system whenthey leave, but you don't want them to have the passcode to disarmthe system. COMMAND 1 arms the system, but it will not disarmthe system. To use COMMAND 1: 1. Ensure that all zones are secure. The display should showREADY TO ARM . 2. Press the COMMAND bar. The display should show SYSTEM COMMAND . 3. Press the 1 key. The display now alternates between ALL SECURE and EXIT NOW. After the exit delay expires, the display shortens to ALL SECURE . 4. To disarm your security system, enter your personal passcodebefore the delay time expires. Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2

Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2