Security: Intrusion

Issue What are the enviromental considerations for the proper operation of the Bosch control/communicators? Solution Indoor Dry.   Relative Humidity 5% to 85% noncondensing at +86 degrees Fahrenheit (+30 degrees Celsius). Operating temperature would be +32 degrees Fahrenheit to +120 degrees Fahrenheit ( 0 degrees Celsius to 49 degrees Celsius ).

How to correct the D8112/5505 not sending a Reboot report. The 8112/5505 panel is communicating alarm and trouble signals but after resetting the panel it does not report the reboot.  5505,D8112A,D8112E1,D8112G1,D8112G2

Getting "check area" on keypad when master arming an area.

Issue Why does the zone light on the D360 Command Center light when the D279A is disarmed? Solution The D8112 panel is programmed with a zone code of 3271 on a particular zone. The purple jumper on the D279A is cut. As a result, the D360 zone light illuminates when the D279A is disarmed. This is normal and will not impact the D8112 arming process.  If the D1252A is used, the disarm state of the D279A is not indicated.

How to program a zone to activate Alternate Alarm. D8112G2,D8112E1,D8112G1,D8112A.

Part numbers D8112, D8112E, D8112E1, D8112G, D8112G1, D8112G2, D1252, D1252A, D8129

How to troubleshoot sending or receiving D8112 programming with the D5200.

How to set configure the D8112 to pulse the bell output on a fire alarm. D8112A,D8112E,D8112E1,D8112G,D8112G1,D8112G2

  How to report a four digit account number with the D8112. D8112E,D8112E1,D8112G,D8112G1,D8112G1,D8112G2  

What socket do I plug the relay (D136) in for switched AUX Power Output? D8112E1,D8112G1,D8112G2,D8112,D8112A,D8112E,D8112G,D136

How to control the D8112 buzz when test reports are sent. The D8112 panel buzzes when it sends test reports, how can I stop the buzz? D8112G2,D8112E1,D8112G1,D8112A

How can the D8112 panel be configured to either send a reboot signal or to recieved a copy of the program from the panel? D8112G1,D8112E1,D8112G2

Issue Can I direct connect RAM IV/RPS to program an 8112?   Solution   No. Only dialup is supported with the 8112.

D8112A

How to troubleshoot a faulted panel zone that monitors D125B 2-wire loops. D9112, D9412 D7212B, D7212B1, D9112B, D9112B1  D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2   D8124 D125B 5924 (Honeywell 9124) 5505 5800, 5800B1, 5800C, 5800G 5900, 5900B, 5900B1, 5900C, 5900G   

What keypads are compatible with a D8112 Series Panel D8112G2,D8112E1,D8112G1,D360,D1252,D1252A

Part numbers D8112, D8112E, D8112E1, D8112G, D8112G1, D8112G2

Part numbers D8112, D8112E, D8112E1, D8112G, D8112G1, D8112G2

The Alpha keypad offered for the D8112 panel series was the D1252 or D1252A   Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2, D1252, D1252A

Issue Command 4 function on the 8112. Solution Reset Trouble Sounder Reset Alarm Memory Display Display Clock COMMAND 4 performs several functions for your securitysystem. Use this command to silence your Alpha II steady troubletone during system trouble events or clear the alarm memory displayof the Alpha II Command Center. Your security system may be programmed with an internalclock. To display the clock momentarily at the Alpha II CommandCenter, enter COMMAND 4. The display will showTEST= (time display) . If the display showsTEST= without the time display, then yoursystem is not programmed for clock displays. All other functionsof COMMAND 4 are still available. To use COMMAND 4: Ensure that your security system is disarmed. Press the COMMAND bar. The display should show SYSTEM COMMAND Press the 4 key. The display should showTEST= (time display) momentarily. If the displayshows TEST= , with no time display,your system is not programmed to indicate time of day.However, resetting the trouble sounder and clearing the alarmmemory display still remain functional. Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2