Security: Intrusion

Issue Silencing the Alarm on an 8112.   Solution   The audible alarm has a specific period of time it sounds before automatically shutting off. If an alarm occurs and you want to silence it before the time expires, simply enter your personal passcode and the alarm will stop. To silence your Alpha II during a service alert, press COMMAND 4 to reset the alarm. To silence your security system: • Enter your personal passcode for audible alarms. or • Enter COMMAND 4 for service alerts. NOTE: Some installations are programmed so that the alarms cannot be silenced until the zone is restored to normal (non-alarmcondition. Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2

How to configure a Timer Test on the D8112. How to creating or modify an existing Timer Test on the D8112 control panel. D8112, D8112E, D8112E1, D8112G, D8112G1, D8112G2

Issue On the Honeywell 520 keypad, NOT AUTHORIZED is being displayed when entering a code and CMD 48 to set up the next test time.   Solution   Only passcodes with authority level 5 (service level) are authorized to use CMD 42 and CMD 48 functions on the Honeywell 5505 using the 520 keypad.

Issue Command 4 function on the 8112. Solution Reset Trouble Sounder Reset Alarm Memory Display Display Clock COMMAND 4 performs several functions for your securitysystem. Use this command to silence your Alpha II steady troubletone during system trouble events or clear the alarm memory displayof the Alpha II Command Center. Your security system may be programmed with an internalclock. To display the clock momentarily at the Alpha II CommandCenter, enter COMMAND 4. The display will showTEST= (time display) . If the display showsTEST= without the time display, then yoursystem is not programmed for clock displays. All other functionsof COMMAND 4 are still available. To use COMMAND 4: Ensure that your security system is disarmed. Press the COMMAND bar. The display should show SYSTEM COMMAND Press the 4 key. The display should showTEST= (time display) momentarily. If the displayshows TEST= , with no time display,your system is not programmed to indicate time of day.However, resetting the trouble sounder and clearing the alarmmemory display still remain functional. Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2

How to Activate the ALT ALARM RELAY on a D8112 Panel. When is the ALT ALARM RELAY triggered? D8112G2,D8112E1,D8112G1,D8112A

Issue How can the D8112 clock be set? Solution COMMAND 45 is used to adjust the time display on your Alpha II Command Center. When you enter COMMAND 4 the Alpha clock is shown in the display momentarily. By entering COMMAND 45, the clock is displayed and may be adjusted with the Alpha II keypad. IMPORTANT: The time should be checked and adjusted at least once a month to insure accuracy. 24-Hour clock settings 1:00pm = 13:00 5:00pm = 17:00 9:00pm = 21:00 2:00pm = 14:00 6:00pm = 18:00 10:00pm = 22:00 3:00pm = 15:00 7:00pm = 19:00 11:00pm = 23:00 4:00pm = 16:00 8:00pm = 20:00 12:01am = 00:01 To use COMMAND 45: 1. Ensure that the security system is disarmed. 2. Press the COMMAND bar. The display should show SYSTEM COMMAND, press 4, 5. 3. Press and release the 4 key, then press and release the 5 key. The display should show SET TIME=(time disply). To set a new time display, simply enter the desired time with the number keys on the Alpha II keypad. (Remember, the clock is set in military time standards, also known as the 24-hour clock. Enter four digits for a complete time setting.) The new time scrolls into the display from right to left, replacing the old display. For example, to set a time of 1:15 a.m. you would enter the following: Press the 0 + 1 + 1 + 5 keys. The display shows SET TIME= 01:15. 4. When the display is correct, press the COMMAND bar to enter the time and exit from this mode. If the COMMAND bar is not pressed, the new time will not be entered and the Alpha II will revert back to the original time displayed. If no keys are pressed for 20 seconds, the Alpha II automatically exits from this mode. Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2, D1252, D1252A

Issue Keypad says "loopback bad" and scrolls thru all the characters.   Solution   Keypad not addressed correctly. Switch dipswitch dip# 1 off   Part numbers D8112A, D1252, D1252A

How to correct the Central Station not getting BFSK Reports.

How to program the D8112 panel to report AC Restoral Reports. Central Station Receiving AC Fail Reports but not AC Restoral Reports. D8112E1,D8112G1,D8112A,D8112G2.

Issue How can the you Manually Transmit System Status Report? Solution Transmit System Status Report COMMAND 42 allows you to send a report to the CentralStation indicating the current condition of your security system. This report is capable of telling the Central Station if your systemor supervised sub-zone controls, are armed or disarmed, reportsthe condition of primary (AC) power and secondary (battery) powerand indicates the condition of the protective zones (whether azone is normal, in alarm, or in trouble). Always call the Central Station before beginning a StatusReport. If the system is working properly, the Central Stationsends a confirming signal which is shown in the display panelof the Alpha II Command Center. To use COMMAND 42: Ensure that your security system is disarmed. Press the COMMAND bar. The display should show SYSTEM COMMAND Press and release the 4 key. Now press and release the2 key. The display shows TEST= (time display)then holds on STATUS . The display changes to STATUS + whenthe signal is acknowledged by the Central Station. Press theCOMMAND bar or any number key to clear the displayafter test. If SERVICE COM FAIL is displayed at the CommandCenter, or if the acknowledgement signal is not received atthe Central Station, enter your personal passcode to cancelthe test. Call the telephone number of the Central Stationand report a "failure to communicate." Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2

How to bypass a point on the D8112. D8112G2,D8112E1,D8112G1,D8112A

Issue How can the calendar be adjusted on the D8112? Solution Perform the following steps: Your security system has an internal calendar which it uses to schedule automatic test reports and other functions. This calendar can be programmed to run a weekly or monthly time schedule. If programmed for a weekly schedule, the display shows the day of the week followed by the number of the day (for example, MON 2). If programmed for a monthly schedule, the display shows the month, followed by the day of the month (for example, MAR 20). To use COMMAND 46: 1. Ensure that the security system is disarmed. 2. Press the COMMAND bar. The display should show SYSTEM COMMAND. 3. Press and release the 4 key, then press and release the6 key. The display should show SET DATE=(date disply). To set a new date display, simply enter the desired date with the number keys on the Alpha II keypad. See the directions on right for month mode or day of the week mode display adjustments.< /FONT> 4. When the display is correct, press the COMMAND bar to exit from this mode. If the COMMAND bar is not pressed, the new date will not be entered and the Alpha II will revert back to the original date displayed. If no keys are pressed for 20 seconds, the Alpha II automatically exits from this mode. Day of Month Schedule: EXAMPLE: To set a date of May 17, you would enter the following: Press the 0 + 5 keys ("05" is the code for May, the fifth month of the year), then press the 1 + 7 keys. The display shows SET DATE= MAY 17. Numerical entries to set month display 01 JAN 04 APR 07 JUL 10 OCT 02 FEB 05 MAY 08 AUG 11 NOV 03 MAR 06 JUN 09 SEP 12 DEC Day of Week Schedule: EXAMPLE: To set the day of week display for Friday, you would enter the following. Press the 6 key. The display shows SET DATE= FRI 6. Numerical Entries to Set Day of Week Display 1 SUN 3 TUE 5 THU 7 SAT 2 MON 4 WED 6 FRI Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2, D1252, D1252A

Issue Installing a used CPU with unknown programming. Solution CPU can have the RAM cleared. Procedure: * This should be done with the CPU off the panel. With the CPU removed off the panel, remove the shroud; find CR2 and U8 on the circuit board. Place a 3 sec short across the banded end of CR2 and the center pin of U8. This will erase ALL Ram memory. Part numbers D8105, D8107, D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2

Part number D8112A

How to interpret the two alternating asterisks (*) on the D8112 command center. D8112G2,D8112E1,D8112G1,D8112A

How to correct the error message  "RAM CARD NOT PRESENT" when updating D5200 handlers.