Security: Intrusion

How to view the panel type and firmware revision.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G,

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G

Issue Cannot access my menu items via the D1260 keypad, but know I the Menu Functions were enabled for the D1260 keypad within the panel program.   Solution   In programming CMD CNTR ASSIGMENT >  MENU KEY LOCK and set to NO. Verify in programming FUNCTION LIST that the functions the required functions are set to Yes for the correct keypad address. Compatible Control Panels • B9512G/B9512G-E • B8512G/B8512G-E • D9412GV4/D7412GV4/D7212GV41 • D9412GV3/D7412GV3/D7212GV31 • D9412GV2/D7412GV2/D7212GV21 • D9412G/D7412G/D7212G • D9412, D7412, D7212, and D9112 with firmware versions 6.40 or higher

Issue Can I change the user text on a 7000-9000 series panel via the keypad? Solution You may only change the users name via a keypad if you have a D1260 keypad.  Follow the steps below to make the changes. >Command 56 then Passcode >Choose the user number and press ENTER >Press the soft key menu item CONTINUE >Press the soft key menu item NAME >Follow the soft key menu to move left/right and to change the characters in the name. >After you done with the modifications press the soft key menu item CONTINUE >If this is correct you press the soft key menu item YES >If it is not correct then press the soft key menu item NO After you have completed your task press the soft key menu item EXIT D1260 Compatible Control Panels • B9512G/B9512G-E • B8512G/B8512G-E • D9412GV4/D7412GV4/D7212GV41 • D9412GV3/D7412GV3/D7212GV31 • D9412GV2/D7412GV2/D7212GV21 • D9412G/D7412G/D7212G • D9412, D7412, D7212, and D9112 with firmware versions 6.40 or higher

How to use the Enter Key Relay function in G series panels.

How to interpret panel reports generated by MISSING Point Events on G Series Panels.

How to Enable Alarm Verification and how it works.

Issue Can I mix Heat Detectors and 2 wire smokes with a sounder when using a D132A Smoke Detector Polarity Reversing Module? Solution No. When a Heat detector goes into alarm it puts a short on the input zone to indicate the alarm. The D132A uses Aux power from the panel when the polarity reversal takes place and since a heat detector does not reset when polarity is reversed, it would put a direct short on the Aux power of the panel. Consequently everything connected to the same Aux power terminals would not function.

Issue How do I clear alarm memory from the keypad?   Solution   On the D1260 keypad there are 4 buttons on the left and 4 buttons on the right side. Next to the bottom button on the right side should be a meesage that reads CLEAR DISPLAY. 1. Press the button beside the CLEAR DISPLAY prompt. 2. Enter your passcode. 3. Press the button beside the CLEAR prompt again. Now alarm memory should be off the display on the keypad.

How to determine why the BFSK/Relay or Output selected in Point Assignments, or points configured with Relay Response=2, do not reset as expected.  

Part numbers D7412, D9412, D7412G, D9412G, D7412GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B6512, B8512G, B9512G, D9210, D9210B, D9210C, B901

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G, D1255, D1255RB, D1255R, D1255W

How to configure the DX4020 for Different Ports.

How to correct when the command center goes blank as soon as the last area arms. Why does the command center goes blank as soon as the last area arms?

How to configure the Swinger Count and use Swinger Shunt.

How to upgrade the D8112 and use existing Popit addresses and/or Popits.

How To Transmit Opening/Closing Reports By Account Number.

How to make a relay trip when a point is faulted. How to use Relay Follow Point, Output Response type or Relay Response Type.

How to troubleshoot problems with popits and Zonex. D7212B, D7212B1, D9112, D9112B, D9112B1, D9127,D8112, D8128A, D8112B, D8128C, D8128D, D8125