Security: Intrusion

Issue Arming perimeter with delays   Solution   Arm the Perimeter with Delays COMMAND 3 is used to arm only the perimeter of your building, leaving the interior of the building disarmed. Once you have entered COMMAND 3, the exit delay time starts. You now have a predetermined amount of time to leave before the perimeter arms. Although this command does not send a "Closing Report" to the Central Station, it will still send alarms. Enter your personal passcode and press ENT to cancel COMMAND 3. Application This arming command is useful in residential systems when you are leaving, but members of your family, a babysitter or a pet are still inside the house. In commercial installations, use this command to rearm your system when you are on the premises, but not yet open for business. This command will not send a "Closing Report" to the Central Station. Arming with COMMAND 3: 1. Ensure that all perimeter zones are secure (interior zones are not armed with this command and may remain faulted while arming with COMMAND 3). 2. Press the COMMAND bar. The Command Mode indicator light comes on. 3. Press the 3 key. The PERIMETER indicator light flashes. This indicates that the system has begun exit delay time. When the delay time expires, the light remains steady. 4. To disarm your security system or cancel COMMAND 3, enter your personal passcode and press ENT before the delay time expires.

The reader sounds a constant tone and is wired correctly.

Overview: Charging circuit is overcharging the battery. Panel is damaged. Issue Reading 15vdc on the battery charging circuit.   Solution   Replace the panel. The voltage regulator is failing on the panel.

How to add ITI transmitters, are they added in normal or faulted condition? D4412, D6412, RF3226, ITI WIRELESS DEVICES.

Glassbreak detectors are designed to listen for specific sounds from breaking glass. The device used for testing must generate the proper sounds for the glassbreak to generate an alarm. If the correct tester is not used, an alarm will not be generated.

How to test the RF280THS wireless smoke used on the D4412 and D6412. When testing the RF280THS by pressing the 'Test' button does not generate a panel alarm.

Issue How many zones is the D4112 Control Communicator capable of having?   Solution   The D4112 Control Communicator has six end-of-line resisitor supervised, hardwire protective zones. There are five standard programmable zones and one nominal 12 VDC powered zone optimized for two-wire smoke detectors

How to correct the error: RS Control Certificate Not Valid. ITS-DX4020-G, DX4020, B420, RPS, Certificate Builder, RS Control iApp

How to correct the Duplicate Point display when adding points into RF programming. D2412,D2812,D2212,D208RF,D216RF  

Definition: Watch Mode Only- This point will not create alarm or trouble responses and will not generate reports to the Central Monitoring Station.  Program the Point: Select Point Type= 0. Select all Yes/No options= NO. Set Alarm Report Routing = 0: No Reports, No Events to Log/Printer. Set Restoral Report Routing = 0: No Reports, No Events to Log/Printer. Select Watch Tone and enable Watch Point: Select [Cmd] + 62 to select the watch tone. Select [Cmd] + 63 to select the watch point(s).

Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2

Issue How many on-board zones does the D6112 Control Communicator have?   Solution   The D6112 Control communicator has eight end-of-line resistor supervised hardwire protective zones. There are six standard programmable zones; one nominal 12 VDC powered zone optimized for two-wire smoke detectors and one nominal 12 VDC powered zone optimized for two-wire glass-break detectors.

Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2

Article describes 6600 buzzer settings

  Cause: When the B420 or B426 has been programmed through the web interface and the setting; Panel Programming Enable has been set to NO, the B420 or B426 Ethernet Communicator module programming screen will look as displayed below with programming parameters not available for changing.   Solution: The card will need to be accessed again through the web interface and Panel Programming Enable must be changed to read YES. Log into the Web-Browser and select Maintenance. Click on the drop-down arrow beside the field; Panel Programming Enable  and change it to Yes. When programming the B420 or B426 to be connected to a GV3 or older panel the web interface is used. When programming the B420 or B426 to be connected to a GV4 panel, use keypad programming.