Security: Intrusion

Overview: Firmware revision 2.20 and higher limit errors when keypad programming a D2212 panel for D208 point expansion.  Issue Why does the D2212 panel not allow keypad programming for a D208 point expander? Solution Before firmware revision 2.20, it was NOT possible to program the D2212 for a D208 Point Expander using keypad programming.  Panels before firmware version 2.20 should be programmed with the D5200 handheld programmer or RAMIV/RPS download software.  Firmware revision 2.20 and above CAN be programmed via the keypad.

  How to determine the zone code used on a 2000 Series panel for a D132A trouble point. D132A,D2412,D2812,D2212  

Overview New RF Receiver Trouble, Receiver ‘Jammed’ When used with RF Receivers with firmware 9.0 (or later), D2212Bs with revision 3.03 firmware (or later) can display two distinct trouble conditions. The receiver trouble display is expanded to two lines. Issue RCVR # TROUBLE 2111 # is the receiver number (7 or 8). RCVR # TROUBLE 1211 # is the receiver number (7 or 8). Solution 2111 in the second line indicates that no sensor has been heard from in a calculated interval. The interval depends on the number of sensors in the system. 1211 in the second line indicates that the receiver is in a ‘jammed’ condition. Interference is at a level that prevents sensor transmissions from being received.

Part numbers D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U, D2812P, D222A, D223A

How do you enable the A, B, & C keys on keypad? D2212,D2112,D2412,D2812,D202,D202A,D220,D222,D223

How to configure the 2000 Series to use 4-Wire smokes. D2212,D2412,D2812 D133, D134

Replacing a D2112 with a D2212 and the keypads do not work D2112,D2212, D202, D202A, D220

When adding zones, they do not display when faulted on the keypad. D2412,D2012,D2112,D2812,D2212, D202, D202A, D220

Issue What handler is used to program the D2812 panel. Solution The D5200 2212 product handler supports the following panels: D2212, D2212B, D2212BE, D2412, D2412U, D2812, D2812U.

How to correct the inability to view troubles by pressing the 4-key on 2000 series panels.

How many keypads can be installed on a 2000 series panel? D2212,D2412,D2812,5600L,5600E,D205 (8 led),D206 LCD,D222A LCD,D223A LCD,D202A,D220A

Part numbers D2212, D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U, D2812P

Issue What is the difference between the D133 an D134? Solution The D133 has a single relay rated at 2A @ 30 VDC – 0.6A @ 125 VAC. The D134 has two relays rated at 2A @ 30 VDC – 0.6A @ 125 VAC. Current draw for the Relay is 40 mA per relay when activated.

How to initiate a programmed test time on 2000 Series control panels.  Does the D2212 Timer Test Need to be Initiated from the Keypad? D2812,D220A (8 led),D2412,D2212,D222A LCD,D223A LCD,D220A,D222,D223

Could not connect to 2212 panel, programmer would say " FAIL PROD ID D5200,D2212

Issue Will an Answering Machine cause the D168A not to answer when accessed locally? Solution Some answering machines load down the phone line and cause it to go below 7 VDC. The D168A needs at least 7 VDC to properly process the DTMF tones.

Which keypads can be used on a D2212 Control Panel? D2212,D222A LCD,D223A LCD,D202A,D220A,D222,D223

How to connect 4-wire Smoke Detectors to D2000 Series Control Panels. D2212B, D2212BE, D2412U, D2412UE, D2812

Issue What revision D2212 panel was compatible the the D169?   Solution   Revisions 2.53 and later panels are compatible with the D169 2-way voice.

Issue Can I mix Heat Detectors and 2 wire smokes with a sounder when using a D132A Smoke Detector Polarity Reversing Module? Solution No. When a Heat detector goes into alarm it puts a short on the input zone to indicate the alarm. The D132A uses Aux power from the panel when the polarity reversal takes place and since a heat detector does not reset when polarity is reversed, it would put a direct short on the Aux power of the panel. Consequently everything connected to the same Aux power terminals would not function.