Security: Intrusion

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G

How to configure the D9210B, D9210C or B901 Access Control Module to require Access Granted to Enter and to Exit.

How To Transmit Opening/Closing Reports By Account Number.

Issue How do I clear alarm memory from the keypad?   Solution   On the D1260 keypad there are 4 buttons on the left and 4 buttons on the right side. Next to the bottom button on the right side should be a meesage that reads CLEAR DISPLAY. 1. Press the button beside the CLEAR DISPLAY prompt. 2. Enter your passcode. 3. Press the button beside the CLEAR prompt again. Now alarm memory should be off the display on the keypad.

Describes how to setup when a valid token is presented at the reader, the alarm system should disarm, and when the door is closed the alarm system should rearm itself.

Issue The FA113 will not arm the panel if it was disarmed from the keypad and will not disarm if panel was armed from the keypad Solution Used as an arm/disarm device, the FA113 is configured to panel zone 74 or 194. Pressing the FA113 Off button sends an OPEN signal to the control panel and pressing the On button sends a NORMAL signal to the control panel. The area should be both Armed and Disarmed by the FA113 for it to function correctly. When the arming state is changed by the FA113, then by another means, the FA113 becomes unable to detect the current armed state of the area and will not respond to the keys pressed. Correct settings for FA113: The transition of the state of point 74 is what causes the area to arm or disarm. • Mode in the D8125INV is set to 4. • Keyswitch Maintained point (Point Type 4) with  Point Response 2, is  required for  the FA113. • Area will arm with a transition from open to normal on point 74. • Area will disarm with a transition from normal to open on point 74. The FA113 is also used for panic on point 75 (7412G) and point 195 (9412G).

Describes how to print panel information.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4

How to configure door control for multiple users with Intrusion panels Part II

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G

How to program  entry delay for motion detectors with a built in popit.

How to program network reporting in a GV3 Version 8.00-8.09 control panel.

How to determine compatibility and address the B420 or B426 IP Communicator.

How to program control panels for Daylight Savings Time.

How to map a relay to one or more alarm points.

Part numbers D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3,D7412GV3, D9412GV3, D7212GV4, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G