Security: Intrusion

How to configure Remote Security Control to work withcompatible alarm panels.

How to activate multiple auxiliary relays on Area Wide or Panel Wide Events.  Programming Area Wide or Panel Wide Relays will only allow a single relay entry.  Use an auxiliary relay such as the D130, D133 or D134 when multiple relays are needed to energize on a panel event.

How to configure Intrusion panel door control for multiple users and access doors

How to use the G Series Battery supervision and Discharge - Recharge Schedule.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G

Issue What is the value for the EOL resistor used with a POPIT? Solution 33K Ohm 1/2 Watt EOL resistor on a POPIT. Ordering Part Number P106F

Use the Menu function ‘MASER ARM’ to arm either selected areas or all areas that the user has authority in, which are in the scope of the keypad.  Previously armed areas remain armed while the remaining disarmed will arm.  For example, if a panel uses areas 1-8 and: The keypad has Panel Wide Scope and the user has authority only in areas 1, 2, 3 & 4, then only areas 1, 2, 3 & 4 will Master Arm. If the keypad has Custom Scope in areas 1 & 2 user has authority in areas 1, 2, 3 & 4, then only areas 1 & 2 will arm. Use the Menu function ‘MASER ARM’: Access the keypad Menus from the keypad. Press the NEXT key until the MASTER ARM ? function is displayed and select [ENTER]. Enter a valid passcode and press [ENTER]. The display shows MASTER ARM ALL ?, select [ENTER]. The command center displays ARMING X,X,X,X…  where X= the available and authorized areas to arm. 

Issue How do I clear alarm memory from the keypad?   Solution   On the D1260 keypad there are 4 buttons on the left and 4 buttons on the right side. Next to the bottom button on the right side should be a meesage that reads CLEAR DISPLAY. 1. Press the button beside the CLEAR DISPLAY prompt. 2. Enter your passcode. 3. Press the button beside the CLEAR prompt again. Now alarm memory should be off the display on the keypad.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G

How to configure a DX4020 for use with RPS.

Describes how to setup when a valid token is presented at the reader, the alarm system should disarm, and when the door is closed the alarm system should rearm itself.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4

How to configure door control for multiple users with Intrusion panels Part II

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G

How to work with points programmed with Relay Response 1 or Output Response 2.

How to configure the D9210B, D9210C or B901 Access Control Module to require Access Granted to Enter and to Exit.