Issue
On 2000 series panel, point codes are programmed for points between 9 and 24. When programmed points are tested the keypad reads "PT(#) PT DISABLED (where # is the number of the point being tested).
Solution
Pt text (Point Text) was never changed from default that read "PT(#) PT DISABLED".
Issue
How many zones can be programmed on the D8112G2?
Solution
The D8112G2 is capable to have 8 master zones that may be expanded to 134 individual zones of protection.
Issue
How many zones is the D4112 Control Communicator capable of having?
Solution
The D4112 Control Communicator has six end-of-line resisitor supervised, hardwire protective zones. There are five standard programmable zones and one nominal 12 VDC powered zone optimized for two-wire smoke detectors
Issue
What are the enviromental considerations for the proper operation of the Bosch control/communicators?
Solution
Indoor Dry.
Relative Humidity 5% to 85% noncondensing at +86 degrees Fahrenheit (+30 degrees Celsius).
Operating temperature would be +32 degrees Fahrenheit to +120 degrees Fahrenheit ( 0 degrees Celsius to 49 degrees Celsius ).
Issue
How many Logger Events can the D8112G2 store?
Solution
The D8112G2 Control Communicator can store up to 400 Events in the panel memory. The panel logs the time, date, event, master zone, and the primary or alternate phone number called for each event. The 400 events can be retrieved with the RAM II, RAM IV or RPS downloading software.
Keypad programming is available in GV3 panels with firmware revision 8.10 or higher.
NOTE: Keypad programming is not available during while an RPS programming session is active, or when any area is armed.
Enter from normal operation:
Press [9]+[9]+[Enter].
Select Keypad Programming. The keypad displays Enter Passcode.
Enter the service passcode (default= 123).
Enter from service mode (reset pin closed):
D1255:
Set the address to 16 with dipswitch: 1-5= OFF and 6= ON. The keypad displays Enter Passcode when the reset pin is closed.
Enter the service passcode (default= 123).
D1260:
Set the address to 8 with dipswitch: 1-3= OFF and 4-6= ON. The keypad displays Enter Passcode when the reset pin is closed.
Enter the service passcode (default= 123).
The following options are available upon entering keypad programming:
Phone Numbers – Phone 1 thru Phone 4
Phone Format - Phone 1 thru Phone 4
Enhanced Comm – Path 1 thru 4
Routing
Route Groups 1 thru 4
RPS Parameters
RPS Passcode
RPS Phone Number
RPS IP Address
RPS IP Port
Area Parameter – 1 thru 32
Account On – Yes / No
Account Number
Command Center 1 thru 16
Enhanced Command Center – Yes / No
Command Center Scope –
User Pass Code
User 0 (Install Passcode)
User 1 (User Passcode)
Point Parameters
D9412GV3: 1-247
D7412GV3: 1-75
D7212GV3 1 -40
Point Index
Disable Keypad Programming
Issue
How can a command function such as CMD 47 be used without entering a passcode at the keypad?
Solution
To use commands without a passcode required, disable the command function under the Authority Level Configuration for all authority levels. This will allow the function to be used without a passcode.
Issue
What is the difference between the D9124 and the D9412G?
Solution
The D9124 is a D9412G with a 24 Vdc PSU and all the needed Fire Accessories for a basic system, all in one large red enclosure. See parts List below.
The D9124 is made up of the following :
D9412GLTB - Control Panel
D9101 - Red Enclosure
D9100 - Carriers Module with the Foolowing parts *
* 2 - D192C - Bell Supervision Modules
* 1 - D8125 - Popex Module
* 1 - D928 - Dual Phoneline Switcher
* 1 - D9142LC - 24Vdc Power Supply
D1256 - Fire Keypad
D1601 - Hardwire Transformer
Overview: The FA422 Programming Cable has a 2 pin female connector at the transmitter end. Inovonics transmitters have 3 pins on them. The center pin on the transmitter is for Data and the 2 outer pins are ground. The 2 pin connector connects to the center pin and either of the outer pins on the transmitters when programming.
Issue
The programming cable for the FA422 receiver only has 2 pins at the transmitter end. How does the 2 pin connector connect to the 3 pin transmitter?
Solution
Connect the 2 pin connector to the center pin and either outer pin. Either way will work.