Security: Intrusion

After adding the RFUN-A Universal Transmitter, the point always shows faulted even though it’s normal.

How to Identify the firmware revision of an intrusion panel.

How to resume normal operation when RPS Diagnostics indicates Panel in Standby=Yes.

How to program the panel to auto arm at the end of a closing window.

Determine compatibility of the wireless interface with the panel type and firmware revision.   B820 Wireless interface and EN4200 receiver. Compatible with GV4 panel types, B-Series panels and B8512G/B9512G. The B820 connects to the SDI2 Bus. ISW-D8125CW-V2 Wireless interface and EN4200 receiver. Compatible with G series with rev6.3+ through GV4 when connected to the Zonex bus or B8512G/B9512G when using the B600 retrofit module. ISW-D8125CW Wireless interface and ISW-EN7280 (ISW-TRL8080/ISW-EN4200) receiver. Compatible with G series with rev6.3+ through GV4 when connected to the Zonex bus or B8512G/B9512G when using the B600 retrofit module. D8125INV Wireless interface and FA400 receiver. Compatible with G series with rev6.3+ through GV4 when connected to the Zonex bus or B8512G/B9512G when using the B600 retrofit module. Determine compatibility of transmitters by the wireless interface type and receiver date code. EN4200 with date code 11048 and newer (date code is yyddd where yy=year and ddd=day): Works with transmitters designated with ENxxxx or ISW-ENxxxx part numbers. EN4200 with date code 11047 and older (date code is yyddd where yy=year and ddd=day): Works only with transmitters designated with ISW-ENxxxx part numbers. Compatible Transmitters designated with ENxxxx part numbers. Requires EN4200 with date code 11048 or newer; EN1223D Water‑resistant Pendant Panic EN1223S Water‑resistant Pendant Panic EN4200 Wireless receiver EN1233D Necklace Pendant Panic EN1233S Necklace Pendant Panic EN1235D Belt-clip Panic EN1235S Belt-clip Panic EN1235SF Fixed Location Panic EN1235DF Fixed Location Panic EN1210EOL Universal Transmitter w/ EOL EN1210W Door-Window Transmitter w/Reed Switch EN1215EOL Universal Transmitter with Wall Tamper & EOL Survey Transmitter EN1215WEOL Door‑window Transmitter w/ Wall Tamper, Reed Switch, & EOL EN1260 PIR Transmitter EN1262 PIR Transmitter EN1265 PIR Ceiling Motion EN1261HT PIR High-traffic EN1242 Smoke EN1247 Glassbreak EN1249 Billtrap ISW-TRL8080 EN7280 Receiver/Translator Kit EN4204R LED Receiver EN4216R LCD Receiver EN5040-T High‑power Repeater EN7016 Wireless Survey Kit EN1210SK Compatible Transmitters designated with ISW-ENxxxx part numbers: ISW-D8125CW-V2 Wireless Interface ISW-EN4200 Wireless receiver ISW-EN1223D Water‑resistant Pend Panic ISW-EN1223S Water‑resistant Pend Panic ISW-EN1233D Necklace Pendant Panic ISW-EN1233S Necklace Pendant Panic ISW-EN1235S Belt-clip Panic ISW-EN1235D Belt-clip Panic ISW-EN1235SF Fixed Location Panic ISW-EN1235DF Fixed Location Panic ISW-EN1210EOL Universal Transmitter w/ EOL ISW-EN1210W Door-Win Transmitter w/Reed Switch ISW-EN1215EOL Universal Transmitter with Wall Tamper & EOL ISW-EN1215WEOL Door‑window Transmitter w/ Wall Tamper, Reed Switch, & EOL ISW-EN1260 PIR Transmitter ISW-EN1262 PIR Transmitter ISW-EN1265 PIR Ceiling Motion ISW-EN1261HT PIR High-traffic ISW-EN1242 Smoke ISW-EN1247 Glassbreak ISW-EN1249Billtrap ISW-TRL8080 Translator ISW-EN7280 Receiver/Translator Kit ISW-EN4204R LED Receiver ISW-EN4216R LCD Receiver ISW-EN5040-T High‑power Repeater ISW-EN7016 Wireless Survey Kit ISW-EN1210SK Survey Transmitter

How to configure the Swinger Count and use Swinger Shunt.

The panel is dialing in Pulse when its programmed to dial in DTMF. How to make the panel dial in DTMF when programmed for DTMF but still dialing in Pulse.

The panel will not send alarm reports and instead is sending an 'ALARM RECENT CLS’ event.

How to lock access to the panel program to prevent take overs. D9112B1, D2012, D2112, D2212, D2412, D2812, D7212B, D7212B1, D8112G2L, D9112, D9112B, D9112B1

How to interpret the heartbeat LED status of the B308 octo-relay module.

How to determine the card data from the B942 credential using the B942 or Remote Programming Software

How to interpret the message Network Modx Cable Open.

How to address SDI2 devices without causing address conflicts. Can different types of SDI2 devices use the same address setting? B810, RFRP-A, B820, B208, B308, B420, B426, B520, B920, B921C, B930, B942.

The Remote Security Certificate Builder panel list is empty Related Products Remote Security Certificate Builder

How to control the Alarm Bell sound during Remote Arming or Keyswitch Arming. The Alarm Bell is sounding when the area is armed remotely or by using a Keyswitch arm point. How can I prevent this?

Related Products B3512 B4512 B5512 B930 D7212GV4 Ver2+ D7412GV4 Ver2+ D9412GV4 Ver2+

How to force Remote Programming Software (RPS) to connect to the panel from a keypad. Remote Programming Software, Answer, 2000 series, D2212, D2412, D2812, D4412, D6412

How to determine the values to enter for the Poll Rate and Ack Wait Time. Note: The calculation described is only be required on legacy control panels.  The B8512G/B9512G and GV4 types only need a Receiver Supervision Time selection.  The Poll Rate, Ack Wait and Retry count will automatically populate.  The formula for determining Poll Rate and Ack Wait Time is as follows: Panel setting: Poll Rate + Ack Wait + ( Retry Count X Ack Wait) Receiver setting: Panel Poll + Ack Wait Panel setting = Receiver setting Example:    Panel Setting: Poll Rate = 240; Ack Wait = 10; Retry Count = 5 Panel setting: 240+10+ (5 X 10) = 300 Receiver Settings: Poll = 240; Ack = 60 Receiver setting: 240 + 60 = 300 300 = 300 Refer to the the following site for more information on setting up Conettix Devices www.conettix.com/Downloads.aspx

How to create a Man-Trap in a G-Series or B6512 Intrusion Panel. How to block use of an access credential if another door is opened.

Cannot silence an alarm using a Custom Function Related Products B3512, B4512, B5512, B6512, B8512G, B9512G, D7412GV4 Ver2+, D9412GV4 Ver2+