Security: Intrusion

Best practices to download and Install Remote Programming Software (RPS).

Issue How do I reset the command center sounder and memory display? Solution Reset Command Center Sounders*Reset Alarm Memory Display COMMAND 4 performs two functions for your security system. Use this command to silence your Command Center sounder during service alert, and to reset the Command Center alarm memory. To use COMMAND 4: 1. Ensure that your security system is disarmed. 2. Press the COMMAND bar. The Command Mode indicator light comes on. 3. Press the 4 key. The Command Center sounder is silenced and any flashing Zone Status indicator lights are turned off if the zone is normal.

Issue How is the D6112 armed and disarmed? Solution Arming Your Security System Your security system can be armed in many different ways, depending on the arming command used. Arming commands are those commands used to arm the system. The most basic arming command is to arm the entire system. This is done by entering your personal passcode and pressing ENT or by entering COMMAND 1. To ARM your security system: Enter your personal passcode and press ENT or enter an Arming Command. Your system may be programmed to send a "closing" report to the Central  Station when arming. Disarming Your Security System Your security system is disarmed by entering your personal passcode and pressing ENT. When your system is armed, you must enter the premises through a designated entry door to prevent an immediate instant alarm condition. Opening the door starts an entry delay time and the Command Center emits a pulsing "beep" tone to remind you to disarm the system. Entering your personal passcode and pressing ENT before the delay time expires and the system will disarm. If you enter through a wrong door or fail to disarm the system before the entry delay expires, you will generate an immediate alarm. To DISARM your security system: Enter your personal passcode and press ENT. Your system may be programmed to send an "opening" report to the Central Station when disarming.

How to determine which pins of the RJ45 and RJ11 are used for Tip and Ring or Tip-House/Ring-House.

Issue How do I Force Arm the System?   Solution   Force Arming the System Under normal conditions your Command Center cannot be master armed while there is a faulted zone. Force arming allows you to arm the system with any zone faulted other than priority zones. (Priority zones are zones that must be normal when the system is armed.) Force arming arms only those zones that are ready to arm; any zone faulted at arming time is bypassed (not armed). When force arming, a trouble report may be sent to the Central Station indicating that the system was force armed and which zone was faulted. A closing report may also be sent by those systems that are programmed for opening and closing reports. Force arming can be programmed to apply to most arming commands as well as your personal passcode. Your alarm technician will check the boxes below to indicate which arming commands can force arm your system. To arm with zones faulted: 1. Enter your personal passcode and press the ENT key, or enter an arming command (COMMANDs 1, 2, or 3). The Command Center then emits a "beep" tone with each keytouch indicating that a zone is faulted. 2. Press the COMMAND bar and then the ENT key. The system now arms all zones which are normal. NOTE: If the fault is restored (returned to normal) while arming, the zone will be armed. If the fault is restored after arming, how your system is programmed determines whether or not the zone will be armed with the rest of the system.

How to force arm the D4112 or D6112 control panel.

How to connect to RPS with the modem connected directly to the Panel. How can I connect to a panel with a modem and only 1 phone line?

How to transmit a manual test report from the D4112, D6112 or D8112.

How to force Remote Programming Software (RPS) to connect to the panel from a keypad. Remote Programming Software, Answer, 2000 series, D2212, D2412, D2812, D4412, D6412

Issue How do I do a local system test? Solution Local System Test It is easy for you to test your security system without sending reports to the Central Station. This local system test is performed only when the security system is disarmed to ensure that your security system is operating properly, and should be used to test your system regularly. COMMAND 44 is used to test your security system. This command tests your Command Center, the system’s sounders (both interior and exterior) and the system’s detection devices. No alarm reports are sent to the Central Station unless a 24-hour zone is faulted (e.g.: panic, fire duress). Contact your Central Station before you test your fire protection system because an alarm report may be transmitted. To test individual detection devices, simply activate sensors and open protected doors and windows one-at-a-time. As detection devices are faulted, the Command Center display panel indicates the faulted zone. This verifies that the detection device is working properly. To use COMMAND 44: 1. Ensure that the security system is disarmed. 2. Press the COMMAND bar. The Command Mode indicator light comes on. 3. Press the 4 key twice. Audible devices (both interior and exterior) sound. To silence the audible warning, press any numeric key of the Command Center keypad. 4. After silencing the audible devices, you may test detection devices. Open a door or a window, or activate a motion sensor. The Command Center display panel indicates the zone which you have faulted. This verifies that individual devices are working properly. 5. To end the Local System Test simply press any numeric key on the Command Center.

Issue What 2 wire smoke detectors have been UL listed compatible with the D4112?   Solution   Note : The D4112 is not UL listed for Commercial Fire Applications. This control does not support multiple detectors in alarm. Do not use smoke detectors from different manufacturers on the same circuit. Radionics Head  D262 / Base D260 (20 per loop) Detection Systems Head  DS200 / Base MB200-2W (10 per loop) Head DS200HD / Base MB200-2W (10 per loop) System Sensor Head 1400 / Base N/A (10 per loop) Head 2400 / Base N/A (10 per loop) Head 2400th / Base N/A (10 per loop) Head 1451 / Base B401, B401B (10 per loop) Head 1451DH / Base DH400 (10 per loop) Head 2451 / Base B401, B401B, DH400 (10 per loop) Head 2451TH / Base B401, B401B, DH400 (10 per loop) Head 2300T / Base N/A (10 per loop)

How to work with the D6112 Battery Discharge and Recharge voltage schedule. When does the D6112 report Low Battery? When does the D6112 report Low Battery Restoral?

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3,D7412GV3, D9412GV3, D7212GV4, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G, D2212, D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U, D2812P, D6412, D4412, B3512, B4512, B5512, B6512

How to work with the D4112 Battery Discharge and Recharge voltage schedule. When does the D4112 send a Trouble Low Battery report to the monitoring station? When does the D4112 send the Low Battery restore report to the monitoring station?

Issue What would cause the D6112 panel to send a zone 9, when arming the system? Solution D5200 Programing - 7.10 or 8.10 = Comb ID is set to yes in the program of the panel. With this prompt set to yes in the program, a zone 9 is sent when the panel is armed by the remote programmer, or command 1.

Overview: D4112 doesn’t arm or anything when code is entered at the keypad. Issue Nothing happens. Doesn’t arm or anything when code is entered at the keypad. Solution Connect programmer using coiled cord. Plug in plastic RJ phone type plug into COMMUNICATOR female connector on 5200 Plug brown connector on other end of coiled cord to programmer connection on 4112 Press ON button on 5200 Type in password at PASSWORD prompt, press enter. Top Line of 5200 shows PRODUCT HANDLERS Using the up/down arrows scroll down until 4112. Please blinking cursor on 4112 Press RED Enter Group button Place cursor on NEWRECORD Short the Standby pin on 4112 to ground momentarily Press RECV(COPY) button on programmer Receiving will be displayed at the top line of the 5200 Display Scroll down using arrow down key until cursor is on 2 PASSCODES Press ENTER GROUP button Passcode1 should have 234 in the field. To change field, press CLEAR key and type in the code to be used. Press enter The code is restricted to 4 characters but the user enters a prefix of 1, 2, 3, 4, 5…depending upon the slot. Example: PASSODE1 shows 234. The user code will be 1234   *** NOTE: Also make sure that the panel has a valid and functioning analog line.  The functionality of the system is dependent upond successful communications.

Issue Arming perimeter with delays   Solution   Arm the Perimeter with Delays COMMAND 3 is used to arm only the perimeter of your building, leaving the interior of the building disarmed. Once you have entered COMMAND 3, the exit delay time starts. You now have a predetermined amount of time to leave before the perimeter arms. Although this command does not send a "Closing Report" to the Central Station, it will still send alarms. Enter your personal passcode and press ENT to cancel COMMAND 3. Application This arming command is useful in residential systems when you are leaving, but members of your family, a babysitter or a pet are still inside the house. In commercial installations, use this command to rearm your system when you are on the premises, but not yet open for business. This command will not send a "Closing Report" to the Central Station. Arming with COMMAND 3: 1. Ensure that all perimeter zones are secure (interior zones are not armed with this command and may remain faulted while arming with COMMAND 3). 2. Press the COMMAND bar. The Command Mode indicator light comes on. 3. Press the 3 key. The PERIMETER indicator light flashes. This indicates that the system has begun exit delay time. When the delay time expires, the light remains steady. 4. To disarm your security system or cancel COMMAND 3, enter your personal passcode and press ENT before the delay time expires.

How to determine the current draw for keypads used on the D4112 or D6112 panels. D4112, D6112, D636, D620, D626, D630, D640.