Security: Intrusion

How to configure the RK40 iCLASS pin reader for 26-bit output. ARD-RK40-09, ARD-RK40-14

Issue What is the difference between the D9124 and the D9412G?   Solution   The D9124 is a D9412G with a 24 Vdc PSU and all the needed Fire Accessories for a basic system, all in one large red enclosure. See parts List below. The D9124 is made up of the following : D9412GLTB - Control Panel D9101 - Red Enclosure D9100 - Carriers Module with the Foolowing parts * * 2 - D192C - Bell Supervision Modules * 1 - D8125 - Popex Module * 1 - D928 - Dual Phoneline Switcher * 1 - D9142LC - 24Vdc Power Supply D1256 - Fire Keypad D1601 - Hardwire Transformer

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, D1255, D1260, D1265

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G

How to determine the max available current for point 1 in the D4412 or D6412.

How to access the IP Communicator Web Browser.

How to select the correct legacy mode or datagram setting for network communications.

How to determine which control panel has SDI 92 available for the IP Communicator. Which is the first panel that supported address 92 for communication devices on the SDI bus. B420, B426, B450

How to use the ISW-D8125CW-V2 and D8125INV on the same panel. Can the D8125INV be connected to a panel that already has an ISW-D8125CW-V2 connected?

Issue Panel is not sending restorals when the point restores.  Log also has no entries for restorals on the point.   Solution   This is normal if the panel is programmed not to send restorals. In RAM/RPS check in the following: Point Index Codes > Point Indexes 1-16 or Point Indexes 17-31 Disable Restorals Default: No    Selections: Yes or No Yes: Disable restoral reports for this point. No: Enable restoral reports for this point. When this option is enabled, a restoral report is sent to the receiver when the point returns to normal after being in an alarm or trouble condition. If you are using the 5200: In the 5200 check under: 9112B > Point Index > Point Index # (where # is a value between 1 and 31 only) press the white ENTER key press the down arrow key (red keys on the 5200) Repeat until you are at P## Disable Restorals Default: No Selection: Yes or No Yes = Disable Restoralreports for this point. No =  Enable Restoralreports for this point. When this option is enabled, a Restoral report is sent to the receiver when the point returns to normal after being in an alarm or trouble condition. Use this item to automatically put this point back into the system.

Issue When programming the D279 keypad point index on the 7000/9000, G, GV2, & GV3 series panels, how should the type and response be programmed?   Solution   Program a type 7 for D279 (O/C Non-Priority): The D279 provides point arming and disarming independent of the area arm state. A non-priority D279 point arm state does not affect the area arm state. Point Response must be programmed 1. Program type 8 for D279 (O/C Priority): The D279 provides point arming and disarming independent of the area arm state. A priority D279 point must be armed before an area can be armed. Program Point Response as 2.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3,

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, 

Part numbers D7412,D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2,D7412GV3, D9412GV3,

Part numbers D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3,D7412GV3, D9412GV3, D7212GV4, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G