Security: Intrusion

Issue Arming perimeter with delays   Solution   Arm the Perimeter with Delays COMMAND 3 is used to arm only the perimeter of your building, leaving the interior of the building disarmed. Once you have entered COMMAND 3, the exit delay time starts. You now have a predetermined amount of time to leave before the perimeter arms. Although this command does not send a "Closing Report" to the Central Station, it will still send alarms. Enter your personal passcode and press ENT to cancel COMMAND 3. Application This arming command is useful in residential systems when you are leaving, but members of your family, a babysitter or a pet are still inside the house. In commercial installations, use this command to rearm your system when you are on the premises, but not yet open for business. This command will not send a "Closing Report" to the Central Station. Arming with COMMAND 3: 1. Ensure that all perimeter zones are secure (interior zones are not armed with this command and may remain faulted while arming with COMMAND 3). 2. Press the COMMAND bar. The Command Mode indicator light comes on. 3. Press the 3 key. The PERIMETER indicator light flashes. This indicates that the system has begun exit delay time. When the delay time expires, the light remains steady. 4. To disarm your security system or cancel COMMAND 3, enter your personal passcode and press ENT before the delay time expires.

How to interpret the indications displayed when performing Command 46.

How to Export a Network Account Database into Excel.

Issue Points are faulted but the panel does not react. Solution Points must be faulted for 500 milliseconds minimum. *When using self resetting devices, some do not latch the contact in the faulted position but do show a fault trip via a latched LED.

How to determine the current draw for keypads used on the D4112 or D6112 panels. D4112, D6112, D636, D620, D626, D630, D640.

  Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2, D192A, D192C

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G,

Issue Can not get the panel to send modem format. Modem is set to yes in the program, and the CS is set to 7. The panel will send BFSK. Solution To report in Modem II format, the following must be set: Be sure the receiver will accept Modem II format. Account number can be a 3 or 4 digit for modem. If using a 3 digit, program a zero as the first digit. Program item 2.3, Modem, must be set to yes. Program item 3.3, AModem, must be yes if using an alternate phone number as well. Program item 2.5, Ack14, must be set to no. Program item 3.5, AAck14 must be no if using an alternate phone number as well. Program item 2.7, Ack23, must be set to no. Program item 3.11, AAck23, must be no if using an alternate phone number as well. When Modem format is selected, the panel will ignore any entries in the CS line of the program.

How to use the ISW-D8125CW-V2 and D8125INV on the same panel. Can the D8125INV be connected to a panel that already has an ISW-D8125CW-V2 connected?

       

Issue When programming through the keypad, what is the nibble to program the RF receiver?   Solution                                     Nibble 1249                            Values: 0  = no RF receiver connected 1  = RF receiver 1 connected, set to address 50 2  = RF receiver 2 connected, set to address 51 3  = RF receiver 1 and 2 connected

How to determine how many network interfaces can be added to the control panel. B420 B426 DX4020

Issue Symptom Why would the keypad display Not Ready, but no zone number is displayed? Probable Cause An invisible zone is not ready. Possible Soultion Enter a valid pin number + off to display the zone number of the invisible zone that is not ready. Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, DS7447

D6412, D4412

Overview When wireless points are faulted, they display as 'Short' to the panel. When the wireless point tamper switch is faulted it will display as an 'Open' to the panel. Issue The panel when using a D8125INV and wireless points shows normal/faulted when point transitions from normal to off normal but the control always shows shorted. Solution Problem may be caused by another point expander connected to the control panel. Remove D8125INV from control panel and determine if points go missing. If points remain active (normal, faulted, etc) the control panel is interfacing with the points through another addressable point expander. Part numbers D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G, D8125INV, ISW-D8125CW, ISW-D8125CW-V2, FA400, EN4200

How to determine why the BFSK/Relay or Output selected in Point Assignments, or points configured with Relay Response=2, do not reset as expected.  

How to use the Remote Reset Command. RPS,RPS Lite

Question Are Radion Wireless and B Series Keypads compatible with D7412Gv4/ D9412Gv4/ D7212GV4 Control Panels? Answer Radion Wireless and B Series Keypads are only compatible with D7412GV4 and D9412GV4 on firmware ver 2.0 or newer panels. D7412Gv4 or D9412Gv4 ver 1.0 can be upgraded to ver 2.0, however older SDI keypads will lose most of their functionality as part of the upgrade The D7212GV4 CANNOT be upgraded. Hence it will never be compatible with either of those devices.

Program network reporting in GV3 version 8.10 and higher control panels.