Security: Intrusion

How to configure Intrusion panel door control for multiple users and access doors

Issue The keypad displays the Access Module Door Point is in trouble. Diagnostics displays the point as missing. Solution T+ (Tamper Input) of the Access Module is an unsupervised input that is normal when open. Upon a short, the Door Point number assigned to the supervised zone of the Access Module is reported as a MISSING PT###.

How to vew the History log on D7000/9000 and G series panels. D7212B,D7212B1,D9112,D9112B,D9112B1.

Overview: Missing points are points that are turned on in programming via the Point Index assigned to anything other than 0  and cannot be found by the panel on the Zonex Loop. This problem may have a number of causes such as; the point is actually not in the field, is wired incorrectly, has a faulty addressing device such as its POPIT or Octopopit, or there may be noise in the data loop. When Points go missing, the panel generates responses based on the point type. Fire points generate Missing Trouble responses, non-fire 24 hour points will generate Missing Alarm responses. Points that are neither Fire nor 24 hour points will generate Missing Alarms when armed and Trouble when disarmed. Issue Panel history shows Missing Alarm. What does it mean? Solution This problem may have a number of causes such as; the point is actually not in the field, is wired incorrectly, has a faulty addressing device such as its POPIT or Octopopit, or there may be noise on the zonex data loop in the field. New Installs - Only a few missing , verify the popits are addressed and wired to the correct zonex loop. (9000 Series Panels Zonex 1 is Addresses 9 to 127 and Zonex 2 is 129 to 247). If all on the same wire run verify the wiring from the last working popit to the first missing popit. Exsisting Install that all was working - All popits missing - Remove all wire from the Zonex terminals for the missing popits (9000 Series Panels Zonex 1 is Addresses 9 to 127 and Zonex 2 is 129 to 247). Only wire the D8125 to the correct Zonex (Out of the panel to In of the D8125  and In of the panel to Out of the D8125). This would remove any D8128 Octopopit Modules and D8129 Relay Modules from the Zonex. Next, remove all loop wiring from the + /- Terminals of the D8125. Using View Point Status fro the Keypad or RPS verify the State of all the popits on the loop by add ing 1 loop at a time until you connect the loop or loops that are causing all to go missing. Once you have the bad loop or loops isolated - Divide and conquor the loop. Go out halpf way and open the loop if the points work go out further on the loop if still missing move back toward the panel and open the loop.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G

How to convert Popit addresses from the D8112G2 to be used on a G-Series panel.

Determine compatibility of the wireless interface with the panel type and firmware revision.   B820 Wireless interface and EN4200 receiver. Compatible with GV4 panel types, B-Series panels and B8512G/B9512G. The B820 connects to the SDI2 Bus. ISW-D8125CW-V2 Wireless interface and EN4200 receiver. Compatible with G series with rev6.3+ through GV4 when connected to the Zonex bus or B8512G/B9512G when using the B600 retrofit module. ISW-D8125CW Wireless interface and ISW-EN7280 (ISW-TRL8080/ISW-EN4200) receiver. Compatible with G series with rev6.3+ through GV4 when connected to the Zonex bus or B8512G/B9512G when using the B600 retrofit module. D8125INV Wireless interface and FA400 receiver. Compatible with G series with rev6.3+ through GV4 when connected to the Zonex bus or B8512G/B9512G when using the B600 retrofit module. Determine compatibility of transmitters by the wireless interface type and receiver date code. EN4200 with date code 11048 and newer (date code is yyddd where yy=year and ddd=day): Works with transmitters designated with ENxxxx or ISW-ENxxxx part numbers. EN4200 with date code 11047 and older (date code is yyddd where yy=year and ddd=day): Works only with transmitters designated with ISW-ENxxxx part numbers. Compatible Transmitters designated with ENxxxx part numbers. Requires EN4200 with date code 11048 or newer; EN1223D Water‑resistant Pendant Panic EN1223S Water‑resistant Pendant Panic EN4200 Wireless receiver EN1233D Necklace Pendant Panic EN1233S Necklace Pendant Panic EN1235D Belt-clip Panic EN1235S Belt-clip Panic EN1235SF Fixed Location Panic EN1235DF Fixed Location Panic EN1210EOL Universal Transmitter w/ EOL EN1210W Door-Window Transmitter w/Reed Switch EN1215EOL Universal Transmitter with Wall Tamper & EOL Survey Transmitter EN1215WEOL Door‑window Transmitter w/ Wall Tamper, Reed Switch, & EOL EN1260 PIR Transmitter EN1262 PIR Transmitter EN1265 PIR Ceiling Motion EN1261HT PIR High-traffic EN1242 Smoke EN1247 Glassbreak EN1249 Billtrap ISW-TRL8080 EN7280 Receiver/Translator Kit EN4204R LED Receiver EN4216R LCD Receiver EN5040-T High‑power Repeater EN7016 Wireless Survey Kit EN1210SK Compatible Transmitters designated with ISW-ENxxxx part numbers: ISW-D8125CW-V2 Wireless Interface ISW-EN4200 Wireless receiver ISW-EN1223D Water‑resistant Pend Panic ISW-EN1223S Water‑resistant Pend Panic ISW-EN1233D Necklace Pendant Panic ISW-EN1233S Necklace Pendant Panic ISW-EN1235S Belt-clip Panic ISW-EN1235D Belt-clip Panic ISW-EN1235SF Fixed Location Panic ISW-EN1235DF Fixed Location Panic ISW-EN1210EOL Universal Transmitter w/ EOL ISW-EN1210W Door-Win Transmitter w/Reed Switch ISW-EN1215EOL Universal Transmitter with Wall Tamper & EOL ISW-EN1215WEOL Door‑window Transmitter w/ Wall Tamper, Reed Switch, & EOL ISW-EN1260 PIR Transmitter ISW-EN1262 PIR Transmitter ISW-EN1265 PIR Ceiling Motion ISW-EN1261HT PIR High-traffic ISW-EN1242 Smoke ISW-EN1247 Glassbreak ISW-EN1249Billtrap ISW-TRL8080 Translator ISW-EN7280 Receiver/Translator Kit ISW-EN4204R LED Receiver ISW-EN4216R LCD Receiver ISW-EN5040-T High‑power Repeater ISW-EN7016 Wireless Survey Kit ISW-EN1210SK Survey Transmitter

How to upgrade the D8112 and use existing Popit addresses and/or Popits.

How to use View Point Status to see the current state of a point. D7212B,D7212B1,D9112,D9112B,D9112B1

How to connect to RPS with the modem connected directly to the Panel. How can I connect to a panel with a modem and only 1 phone line?

How to configure the DX4020 for Different Ports.

Article describes how the time is synchronized for Netcom accounts in the D6600 receiver

How to interpret the panel executing Skeds 41-56 when only skeds 1-40 are available. Why does the panel shows Skeds between 41 and 56 executed when only skeds 1-40 are available in programming?

How to build a D8125INV programming cable using 2 standard keypad harnesses.

Issue How is the history reset after an event overflow message?   Solution   Receive the panel's history, choose the set pointer option to have panel start history from that point forward on newer just receiver Current.   Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3,D7412GV3, D9412GV3, D7212GV4, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G

Getting "check area" on keypad when master arming an area.

How to integrate existing Inovonics devices and Radion on the same panel.

How to determine the values to enter for the Poll Rate and Ack Wait Time. Note: The calculation described is only be required on legacy control panels.  The B8512G/B9512G and GV4 types only need a Receiver Supervision Time selection.  The Poll Rate, Ack Wait and Retry count will automatically populate.  The formula for determining Poll Rate and Ack Wait Time is as follows: Panel setting: Poll Rate + Ack Wait + ( Retry Count X Ack Wait) Receiver setting: Panel Poll + Ack Wait Panel setting = Receiver setting Example:    Panel Setting: Poll Rate = 240; Ack Wait = 10; Retry Count = 5 Panel setting: 240+10+ (5 X 10) = 300 Receiver Settings: Poll = 240; Ack = 60 Receiver setting: 240 + 60 = 300 300 = 300 Refer to the the following site for more information on setting up Conettix Devices www.conettix.com/Downloads.aspx

How can a SKED be disabled or changed? D9412G,D7412G,D7212G,D1255,D1260,D7212,D7212B,D7212B1,D7412,D9112,D9112B,D9112B1, D9412GV2,D9412GV3,D9412GV4,D7412GV2, D7412GV3                                                                       

How to address the B901 or D9210C on the SDI bus and how does the panel report an SDI Trouble.