Security: Video

Related Products Bosch Video Client Question How do I backup the complete BVC configuration in Windows 7? Answer If BVC was installed whilst logged into Windows as the Administrator, go to the following folder: C:\Users\Administrator\AppData\Roaming\Bosch\Vidos. Copy the conf folder. This folder contains the BVC configuration. Note : Backup  configuration only applicable to the specific BVC version during configuration restore.

What are the best practices for surge and lightning suppression?

Dear users, have you ever wondered how to best transition from the Project Assistant to (B)VMS? This article aims at providing you a recommendation and the answer is quite simple: Use the Project Assistant to its full extent and once the cameras are connected to the target network, perform a network scan using the BVMS Configuration Client, to add the respective cameras to the system. The remaining fine-grained settings can then be tackled within BVMS.  For details, please check out the attached presentation. Let us know, if you have further questions and share your comments below. Best regards, Your Bosch Security App Team    

The technical note in the attachment describes how to track ships using Intelligent Video Analytics with FW 6.30, how to configure this and what the limitations are.

The attached technical note describes w hich camera settings influence the performance of Essential or Intelligent Video Analytics in Bosch IP cameras, and what the best practices are.

The attached technical note describes h ow to benchmark and differentiate video analytics solutions.

There are several Video Content Analysis (VCA) algorithms available in Bosch IP cameras: Tamper Detection, MOTION+, Essential Video Analytics, Intelligent Video Analytics and Intelligent Tracking. To receive alarm events from them and visualize the results, a client is needed. Each client can choose to present only a part of information and in a different way. The attached technical note gives a high-level overview of the clients supplied by Bosch and the different integration possibilities into 3rd party systems available today. Further information concerning integration into 3rd party software can be found at the Integration Partner Program (IPP) webpage.

The tech note in the attachment describes how to set up map displays of objects detected and tracked by Intelligent Video Analytics, Essential Video Analytics or Intelligent Tracking with FW 6.4x and Video Security Client 2.1.

The technical note in the attachment details device-specific as well as version-specific differences of Intelligent and Essential Video Analytics from FW 4.0 up to FW 6.60.

Related Products DIVAR AN 3000 DIVAR AN 5000 How to configure Monitor B output for Divar AN 3000-5000 Solution see attachment.

Use the project assistant to commission multi-camera projects and generate project reports. Available for Windows and iOS and Android. (status 2018-08-06 / Version 1.1)

Can I upgrade existing BVMS Pro system to a BVMS Enterprise system?

Related Products - VJD-3000 Question How to display MPEG 4 video on VIDEOJET decoder 3000 ? Answer No. VIDEOJET decoder 3000 is only capable of decoding H.264 video.

This will let you call up cameras on an Allegiant monitor output across the network to a remote site.

Connections and programming for VIP X1XF and VG5 600 Dome.

Related Products DiBos version 8.0 to 8.7 BRS version 8.8 and later   Question How to configure LDAP in DiBos / BRS?   Answer See attached 8 screenshots which guide through the LDAP configuration. Known restrictions on the AD: - users and user groups must be located in the same directory in the AD - DiBos / BRS supports max. 1000 user groups in the AD - Comma separated user (ex. User, John) are not supported.

Related Products VRM Question Can I import Direct-to-iSCSI recordings into VRM? Answer No. iSCSI arrays used in Direct-to-iSCSI recording mode must be formatted when imported into VRM.

Related Products All IP encoders Answer Copy/Paste the selection below to your alarm task editor and save. This script will make your encoder trip relay 1 only when IVA rule #1 alarm is active. // Set TempState to monostable mode, 5 seconds OperationMode monostable := { High(50) }; TempState(1) := monostable; if (VCARule(1,1)) then TempState(1) :=true; if (TempState(1)) then Relay(1) :=true else Relay(1) :=false;

Related Products All IP encoders   Answer Copy/Paste this example into the alarm task editor and save.  See comments below for more details, annotated by //. // Settings for JPEG posting JpegPosting PicPosting := { IP( "put ftp FQDN servername or IP here" ) Login( "anonymous" ) Password( "anonymous" ) Format( Large ) FileName( "Snap" ) Suffix( Date ) Camera( All ) }; // Define Operation Mode to periodic, 15min low and 0.1 second high OperationMode periodic := { Low(18000) High(1) }; //define logic TempState(1):=periodic; if(true) then TempState(1); if (TempState(1)) then PicPosting;

Related Products Bosch encoders Answer Place this in the alarm task editor and save it.  Please read the comments for more details.  They are noted below by //. //Define weekly timer from Monday to Sunday from 7am to 9pm Timer weekly := {TimeBegin(07:00) TimeEnd(21:00) DayBegin(Mo) DayEnd(Su) }; //define what is to be recorded Recording recording:= { Camera(All) }; // Define Operation Mode to periodic, 1 sec low 30 min high OperationMode periodic := { Low(10) High(18000) }; TempState(1):=periodic; //define recording timer OperationMode monostable := {High(50)}; TempState(2):=monostable; //Turn on recording timer if (IsActivated(weekly)) then TempState(1) := true; if (TempState(1)) then TempState(2) := true; if (TempState(2)) then recording else Stop(recording);