Never lose track of an object of interest! Intelligent Tracking automatically zooms in to and follows a selected Intelligent Video Analytics object as far as possible with the camera.
For AUTODOME / MIC IP 7000, this means automatically steering the camera to zoom in to the object and follow it.
For a FLEXIDOME IP panoramic 7000, Intelligent Tracking is available in the Virtual PTZ video and steers the dewarped cut-out.
For DINION / FLEXIDOME IP 7000 / 8000 cameras, Intelligent Tracking can steer a region of interest (ROI) stream. This article describes how to set Intelligent Tracking up with FW 6.30 and lists the differences based on the camera types.
Relates to: IP Storage/PC HW - DIVAR IP 6000 R2 and DIVAR IP 7000 R2
Both DIVAR IP units running the BIOS from American Megatrends Inc. (A.M.I)
There are PRE BOOT or POST BOOT beeps.
Please see the following Acoustic Error Codes.
The BVMS Project Checklist is an Excel-based tool which makes it easier to design a BVMS system.
This article describes how to use the project checklist.
Pick the attachment you need, depending on the version of BVMS you have
Until some years ago, new released cameras, encoders, domes and decoders that were introduced into market after a BVMS release could not be connected to an existing BVMS version because these cameras where not known to the BVMS.
In the BVMS 4.5.1, a new concept was introduced.
This concept treats Bosch video encoders and decoders as generic devices, and automatically recognizes specific device functionality (for example the number of streams, relays and inputs).
Based on this information, unknown device is added to the system and can be used by the operator.
The attached document provides a detailed description of this functionality.
The attached manual provides information for Mobile Video Service (MVS) within Bosch Video Management System.
You can find: - how to configure the router and Internet Information Service (IIS) - how to add MVS to BVMS - user guide - some troubleshooting tips
This document can also be found online here.
Trying out the BVMS Lite is easy!
Download BVMS Lite from the Download Area and use the quick installation guide to set-up the system.
BVMS Lite contains
8 video channels
1 intrusion panel and can be used without a time limit.
BVMS Lite can be expanded to 42 channels using license extensions.
A step-by-step instruction on how to install the BVMS Lite demo license can be found to this page.
This article explains how to integrate the Bosch MIC IP 7000 HD camera series into any existing analog CCTV system using the Bosch VIDEOJET decoder 3000. The most common integration scenarios are listed below:
Simple integration using direct connectivity to analog monitor and joystick, typically found in single camera installation (for example, mobile surveillance vehicles)
Integration into an existing analog matrix switcher typically found in large installations (such as for city surveillance)
The Smart Notification service lets your end-customer easily keep track of business operations. Detection, notification and storage of events like warehouse access, POS transactions or goods delivery enable efficient monitoring and resolution of critical events for the business owner.
Please follow below steps to set up a Smart Notification service.
What should you know about SNMP and Bosch cameras SNMP support?
This article explains briefly the basics of SNMP. Declares the basic terms of the protocol. It also explains what part of the protocol is supported by Bosch cameras.
Basics of SNMP and terms.
Simple Network Management Protocol (SNMP) is a common protocol to monitor the health status of a system. Such a monitoring system typically has a central management server that collect all the data from the system’s compatible components and devices. SNMP provides two methods to gain the system health status:
–The network management server can poll the health status of a device via SNMP requests.
–Devices can actively notify the network management server about their system health status in case of error or alarm conditions through sending SNMP traps to the SNMP server. Such traps must be configured inside the device.
Details how to configure Bosch camera to send SNMP traps - How to activate the SNMP and configure sending SNMP traps from Bosch cameras?
SNMP also allows configuration of some variables inside devices and components. The information, which messages a device supports and which traps it can send, is derived from the Management Information Base, the so-called MIB file, a file that is delivered with a product for easy integration into a network monitoring system. There are three different version of the SNMP protocol:
–SNMP version 1
SNMP version 1 (SNMPv1) is the initial implementation of the SNMP protocol. It is widely used and has become the de facto standard protocol for network management and monitoring. But SNMPv1 has become under threat due to its lack of security features. It only uses ‘community strings’ as a kind of passwords, which are transmitted in clear text.Thus, SNMPv1 shall only be used when it can be assured that the network is physically protected against unauthorized access.
–SNMP version 2
SNMP version 2 (SNMPv2) included improvements in security and confidentiality, amongst others, and introduced a bulk request to retrieve large amounts of data in a single request. However, its security approach was considered way too complex,hindering its acceptance. Thus, it was soon pushed out by version SNMPv2c, which equals SNMPv2 but without its controversial security model, reverting to the community-based method from SNMPv1instead, similarly lacking security.
–SNMP version 3
SNMP version 3 (SNMPv3) mainly adds security and remote configuration enhancements. These include improvements on confidentiality by encryption of packets, message integrity and authentication. It also addresses large-scale deployment of SNMP.
Bosch cameras SNMP
To check what SNMP version does a particular camera support, check the data sheet of the device. (Find it under your device in the product catalogue - https://www.boschsecurity.com/xc/en/product-catalog/)
since FW 6.40 onwards Bosch devices support SNMP v1 legacy and SNMP v3
Don't skip the Warning Signs that suggest an HDD Failure.
If you suspect that your hard drive has failed and you are contacting the Central Technical Support team, please first consider the mandatory information listed below, which must be provided to them.
🛈 Port Forwarding
Allows remote computers (for example, computers on the Internet) to connect to a specific computer or service within a private local-area network (LAN).
In a typical residential network, nodes obtain Internet access through a DSL or cable modem connected to a router or network address translator (NAT/NAPT). Hosts on the private network are connected to an Ethernet switch or communicate via a wireless LAN. The NAT device's external interface is configured with a public IP address. The computers behind the router, on the other hand, are invisible to hosts on the Internet as they each communicate only with a private IP address.
When configuring port forwarding, the network administrator sets aside one port number on the gateway for the exclusive use of communicating with a service in the private network, located on a specific host. External hosts must know this port number and the address of the gateway to communicate with the network-internal service. Often, the port numbers of well-known Internet services, such as port number 80 for web services (HTTP), are used in port forwarding, so that common Internet services may be implemented on hosts within private networks.
The IP camera address is always the key if you would like to monitor or remote viewing it. Like any network device, the camera is assigned an IP address when it is connected to the router with Internet access and powered on.
Here we will introduce 3 ways to find the network camera IP address quickly and easily.
A transfer of the license from the Bosch Software License Manager System (SLMS) to the Bosch Remote Portal is required for every BVMS system to be upgraded from 10.1 to 11.0
Starting with BVMS 11.0 the license activation will be done via the Bosch Remote Portal.
To upgrade an existing system, the BVMS licenses need to be migrated from the old licensing system, Bosch Software License Manager System (SLMS), to the new licensing system available in Bosch Remote Portal.
This article describes the steps that need to be followed when upgrading a system to BVMS 11.0.
Prerequisites for upgrading a system to BVMS 11.0:
Existing license activated in SLMS
Valid Software Assurance (SMA) PRO
Valid account on Bosch Remote Portal
❗ ❗ ❗ IMPORTANT
In BVMS 10.x the computer signature is the link to the license in the SLMS
When upgrading to 11.x the computer signature becomes obsolete and the new Remote Portal tool no longer takes it into consideration
The software Order ID is transferred in the background from SLMS to the Remote Portal
This allows the activation of BVMS 11.x in the Remote Portal using the new identifiers for the Management Server Hardware called System Fingerprint, contained in the System Info file.
In terms of license activation process and compared to other versions of BVMS (<v11.0), the Bosch Remote Portal replaces the Bosch Software License Manager System (SLMS), starting with BVMS v11.0.
A new user registration is required in Bosch Remote Portal and the mandatory information for license activation is the System Info file (generated in the Configuration Client) and the Software order ID (received from the Bosch order desk by e-mail → ordering remains unchanged: still utilizes the Bosch Order Desk)
The remote portal will then provide a "Activation file" which includes all activation details. It needs to be uploaded to the newly installed BVMS system.
The activation process defines the start date of the software maintenance agreement (SMA - software assurance) period.
The end date is shown on the License manager of the BVMS Configuration Client after activation
NEW: Software version-less ordering process: Ordering a BVMS Base or Expansion licenses is not software dependent anymore starting with BVMS 11.0 upwards. During license activation only "non End of Life" (EOL) versions are assigned to the license.
Follow this article and find out the steps that need to be performed when activating a new BVMS 11.0 license.
This article will guide you through the upgrade procedure of a MIC 500 camera.
Connected by use of USB / RS485 converter.
Do not use the “Transparent” USB converter anymore as this is not compatible the latest version of Universal Camset Software 4.12
Make sure that you have the MICUSB485VTR2 ( USB to RS485) This converter is attached in package of MIC 500 camera.
Make sure you have programmed on your PC latest Firmware of Camset Software.
Version 4.12 includes the MIC file1.07 which contain all available protocols.
In case Bi-phase card has been inserted in Power Supply box, remove this PCB during upgrading of your MIC camera, in very few cases this may be cause a connection failure during upgrade process.