Security: Video

If for any reason, later on the DIVAR IP needs to be removed from Bosch Remote Portal connected via System Manager, follow the steps from this article.

This article shows the blueprints for the three operation modes that the DIVAR IP supports, combined with Remote System Management. They show the capabilities and limitations of Remote System Management in each of the modes.

Health monitoring with Remote System Management is very easy, as in one page you have an overview of the state of all DIVAR IPs connected to your Remote Portal and then, drilling down a level, you have an instant overview of the state of the cameras connected to the selected DIVAR IP. A service is available to setup health alerts for devices via email, so you are informed when any emergencies pop up.

Bosch's Remote System Management service allows you to leverage the power of the Internet of Things (IoT) to provide secure, transparent, and cost-effective asset management throughout the lifecycle of a video system. This service enables end users, system integrators and installers to perform inventory and update management, as well as health monitoring tasks for an entire Bosch video system (DIVAR IP + BVMS + cameras) from one centralized Remote Portal platform.

This article explains why cannot select the 1080 resolution in the dewarp mode of FLEXIDOME panoramic 5100i 12MP.

With the new VRM eXport Wizard, we offer the possibility to use CLI commands to do exports without needing to open the application.

Configuration Manager 7.60 by default will only trust CA signed certificates. Changing the security requirements will change the behavior of how CM displays the connection/access.

Have a look at this article and learn how to fix the Add Scriptlet button which does not become active. It stays grayed out. Same happens with ClientScript and ServerScript.

If you want to be able to replay the recording for the complete retention time, you should use VRM replay. VRM should be accessible and added to the VSC

"Show VCA items" is a function which works in Internet Explorer 11 with the Bosch MPEG ActiveX installed. Due the end-of-life of Internet Explorer, this function is no longer available on Microsoft Edge.

Upon powering on the DIVAR IP all-in-one 7000 system you hear FAN spinning normal, LEDs are blinking at normal frequency and there are no error beep codes. However, there is no display when connected via VGA (or) DVI (or) DP. Check out this article and find out how to fix this!

Can I mask areas that should not trigger an alarm (e.g. false detection due to sun reflection)?

At startup, a black screen is showing up and it is impossible to boot into the BIOS or attempt a reset by pressing the F7 key. How to fix this?

In this article is explained step by step how to collect System Manager logs from your DIVAR IP all-in-one 4000 & 6000.

In this article can be found which is the max. iSCSI recording sessions of DIVAR IP AIOs.

  Important note Currently, the VRM is itself very seldom used in combination with Genetec. Starting with 2022, Genetec developed a new driver for Bosch cameras “Hybrid driver for CPP13/14+”. With this, the VRM is not considered anymore. With the old “Legacy (CPP7.3 and older) the VRM is still supported.      Related Products: VRM, Genetec Security Center Overview: It is possible to use VRM free of charge (no extra VRM license is required) within Genetec Security Center. Genetec is sending encrypted secret to the VRM server with the number of the licensed channels. When VRM receives and validates this, it can be used for that number of channels for 24 h. A periodic license update is send by Genetec, so the VRM licensing is guaranteed as long as it is used with Genetec Security Center. Default settings, if not extra configuration is needed or done. -License for 1000 Cameras - License update is done every hour   How to license more than 1000 cameras or change the license update period for VRM within Genetec Security Center: Open the Config Tool and Launch a Video Task Select the Archiver Go to the Resource Tab and click on Extensions From the Tab Installed extensions select Bosch. In the Tab VRM add a new VRM and/or select already configured VRM. Click on Advanced settings and add the following parameters If you need to license the system with more than the default 1000 licenses – create the parameter with Name VrmLicenseRequestCount and as value put the required number of licenses. The parameter name is case sensitive If you need to change the duration of the period between each license request (there is always one license request when the archiver starts) – create the parameter with Name VrmLicenseRequestPeriod. The duration of the period is in milliseconds. The default value is one hour. If the value is set to 0, the license request are disabled. The parameter name is case sensitive     Press Enter to confirm the entry and then Close Press Apply and then OK. At the webpage of the VRM one can check if the number of licenses is changed. If you would like to know how to replay the recordings from a Bosch camera managed by Bosch Video Recording Manager (VRM) in Genetec Security Center software, please follow this video: How to use VRM recording in Genetec Security Center   Note:  To support customer needs and to leverage the most important features of Bosch cameras (like data security, Video Analytics, and intelligent bitrate management), the agreed focus of Bosch and Genetec is on the Genetec Archiver Recording Solution. Current and future developments are focused on this recording solution and the VRM in Genetec will only be supported to maintain existing and upcoming projects where a VRM solution is selected. There will be no development of new features. In this maintenance mode, the following is possible: • Certification of new VRM versions (for projects)* • Certification of new DIVAR IP’s* *Requirement: stable API on VRM side Note: The VRM itself might offer more functionality not covered with the integration in Genetec.

In contrast to the moving objects detected in general by IVA 7.10, Camera Trainer allows detection of both moving and non-moving objects, separates, and immediately classifies them. Learn more about Camera Training from this article!

This article lists different ways to connect to cameras Live/Playback using the Video Security Client/App: to DIVAR IP AIO/BVMS system or to Camera directly, bypassing DIVAR IP AIO/BVMS system.  

For VRM (Video Recording Manager) stand-alone Systems and Servers with VSG (Video Streaming Gateway) installed, it is strongly recommended to check for Microsoft OS updates before the VRM Master Installer is installed/updated.

This article explains steb by step how to create the VCA fields for multiple presets in Configuration Manager.