Security: Video

This article shows from where can I find my Bosch Remote Portal ID.

Health monitoring with Remote System Management is very easy, as in one page you have an overview of the state of all DIVAR IPs connected to your Remote Portal and then, drilling down a level, you have an instant overview of the state of the cameras connected to the selected DIVAR IP. A service is available to setup health alerts for devices via email, so you are informed when any emergencies pop up.

This article explains step by step how to do the configuration of a camera & VJD 7000 & Monitor Group integrated in BVMS 11.1.1.

Follow the steps from this article to set up a Live Intervention service in Bosch Alarm Management.

Perhaps you are wondering how to set the maximum retention time on a Divar Network? Some of our customers asked about this option. Well, in DIVAR Network and Hybrid there is not retention time. But you can set the automatically deleting time, that is more or less the same.   Step-by-step guide:   Open one Browser and type your device IP address Login with the administrator account Go to Settings > Storage > Recording Fill in the box with the desired automatic deletion time   Another option is to make this change directly in the local interface of the unit.

If you need to contact Bosch Security Systems by phone, this article provides a full list of phone numbers for all regions and countries that receive support.

Find out from this article how to configure a singe mode VIF on NetApp array. For example if we have 2 (or more) physical interfaces, how to connect them to different network segments and, if one of the segments fails, the second network interface to step in automatically?

Is DIVAR IP 6000 R1 compatible with VRM v.3.83.0021 (64-bit) and BVMS Viewer 10.1?

VIDEOJET decoder 3000 is only capable of decoding H.264 video.

This article is applicable for all the requests related to third party products integrated in Bosch Video Management System Software over ONVIF.

Check this article and find out if you can add and see a BVMS 11 system running on a DIP in MVS webpage as unmanaged site

Configuration Manager 7.60 by default will only trust CA signed certificates. Changing the security requirements will change the behavior of how CM displays the connection/access.

When smoke or fire is been detected, AVIOTEC will sent a Smoke/Fire event to the Alarm Management and at the same time trigger it’s output.  Using this output status, we are able to trigger the Alarm Management.

This article explains what you can do when the message:“The number of windows in this view exceeds the maximum limit set in the system parameters” appears in Operator Client with minimum 2 Monitors.

This article gives you more information about FLEXIDOME IP starlight 8000i camera streaming capabilities.

With the DSA E2800 Bosch introduced Multipathing. It is a fault-tolerance technique that defines more than one physical path between the camera and its iSCSI storage devices through redundant network connections. When using this feature, recording of video data and replaying video data is possible even in case of an iSCSI controller failure. To ensure also that outages of infrastructure equipment (e.g. Switch) could be covered, we recommend following Interconnection.  

Connections and programming for VIP X1XF and VG5 600 Dome.

Upon powering on the DIVAR IP all-in-one 7000 system you hear FAN spinning normal, LEDs are blinking at normal frequency and there are no error beep codes. However, there is no display when connected via VGA (or) DVI (or) DP. Check out this article and find out how to fix this!

This article explains how to configure a single camera that already has a fixed IP address assigned, using Project Assistant App.

If you have the option "Extended (security)/configuration mode" active on a VIDEOJET decoder 7000 (VJD-7513) in Configuration Manager, then no video image will be shown and the BOSCH logo will be displayed at the cameo of the monitor output of the decoder. This is as designed in Configuration Manager, and this mode is to give you the opportunity to enable the SSD Encryption and to disable the USB ports. Once you are finished changing the extended security features, you must uncheck the check box and the decoder will go back to normal functioning.