Security: Video

This article presents what's new in Video Security 3.7 for Windows, Android and iOS.

The Release Letter for CPP 7.72.1118 provides information about the dependencies between firmware versions for a better understanding of the upgrade process of devices with older firmware.

This troubleshooting guide, will guide you through the recovery steps of a DIVAR IP 6000 or 7000, DIVAR IP 6000 R2 or 7000 R2, without video data loss

The timeline is present, but the recordings appear to be black for all cameras.

You may need the SNMP MIB file when you are trying to monitor the camera through a Bosch or 3rd party software. This article aims to describe how to find and enable the SNMP on a Bosch camera.

Find out from this article what is the domain name used to connect your DIVAR to the Remote Portal

If you have CPP4 cameras with 6.11 firmware (FW) version and you need to upgrade them to the latest version, normally you have to upgrade to an intermediate firmware version first. But where you can find this firmware ?

This article contains the scriplet that on Input sends a RCPP command on Input to another camera to close its Relay 1.

This article is a step-by-step guide regarding how to change the Bosch Camera name.

This article explains what is the Intelligent Dynamic Noise Reduction (iDNR) in Bosch cameras.

When doing a pull point subscription, at the Start of the events Rule Engine/LineDetector/Crossed is missing, even though the rule is configured, and is given in the GetEventProperties response. The topic name space for RuleEngine/ FieldDetector/ ObjectInside works as expected.

In order to determine the Time Zone values, perform the bit mask operation of the flag value with the combined bit mask value 0x1F800000 as shown below. Bits 23-28 correspond to the Time Zone bits in the Flags.

Limited user is available on DIVAR IP all-in-one 4000, if the unit has HDDs inside. Every setup with DIVAR IP System Manager, on any DIP (AIO 7000 GEN 3, AIO 4000, AIO 5000, AIO 6000) that is "00N" (without HDDs) will fail and result in a lack of a "limited user" and "kiosk mode", if you do not insert the HDDs and perform the necessary steps from the manual.

The following instruction describes how to configure a data partition from RAID 5 to RAID 6 on the DIVAR IP all-in-one 7000 4th generation. It is not possible to directly migrate from RAID 5 to RAID 6, so the first step is to delete RAID 5 and then create RAID 6.

The thermal mode is saved in the preposition settings. If you have changed the thermal mode of the camera in the Picture Settings Thermal page and you also want the Thermal color mode to apply to the existing saved pre-position, you have to re-save the pre-position again.  

Aside from configuring the camera using its own browser, there are other tools you can use to setup the camera. The choice when using which tool will come down to the individual installer. Their experience and know-how of the tool will dictate which one they will use. 

What FW versions did Crowd Density Estimation get removed from IVA Pro? What to use in replacement for Crowd Density Estimation? How to remove the unrecognized task?

By default, the DIVAR IP all-in-one 7000 devices are intended to operate with one or two local monitors, connected to HDMI interfaces on the rear of the unit. If NO HDMI is connected, then iKVM over BMC port is active and available. In this case, it is supported to remove VGA cover and use it as local admin monitor, not to run the Operator Client.

The Table view provides the option of presenting a summary of specific settings for individually selected devices in the form of a clearly arranged  table.  The content of all main tabs and sub-tabs can be exported in *.csv format.

The "User Manual Bosch AI Alarm Verification Plugin for Milestone XProtect" is a comprehensive guide designed to assist users in integrating and utilizing the Bosch AI Alarm Verification Plugin with the Milestone XProtect video management system.