Security: Video

The unit can receive the time signal from a time server using various time server protocols and then use it to set the internal clock. The device polls the time signal automatically once every minute. To check the NTP connection from the camera please follow this article.

The haneWIN DHCP server software implements a DHCP and BOOTP server based on RFC 2131. The DHCP Server is implemented as a native service for background operation, A Control Panel applet provides interactive access to the service. The server supports automatic DNS updates for DHCP configured clients. The latest version is available and can be downloaded from here. According to the Installation Manual of the DIVAR IP 7000/ 6000: All DIVAR IP systems are preconfigured with default network, user and iSCSI settings. By default, the virtual network adapter (the two physical NIC ports are teamed by default) is configured to obtain a valid network address from a DHCP server in the local network. The haneWIN DHCP server software supports multiple address pools for dynamic IP address assignment as well as fixed IP address assignment to clients.

Are you looking for the MIC IP fusion 9000i Wiper/Washer RCP command syntax to incorporate it in the third party software?

When dealing with 3rd party or VSG, it’s recommended to get at-least "1" I-frame every second (normal scene).

This article provides a step-by-step guide about how you can disable UPnP of Bosch IP cameras & multicast scan from Configuration Manager. One of the reason why UPnP (Universal Plug and Play) is enabled in our devices is because ONVIF uses this to scan the ONVIF device in the network.

If you want to improve the image quality of your Bosch camera and you did not find the FPS option in the Web User Interface, please follow this article and you will find the answer.

This article describes how to set LUNs on a target to Read Only via Configuration Manager.

See what you can do when MIC 7000i with FW 7.72 shows blurred images. After restart, the quality of the image is good for a short time, but the issue reappear.

Follow this article and find out how to store a snapshot of all cameras automatically from the Operator Client

Monitor Group gives operators flexible control over the content of a video wall or allows them to let the system take over this control automatically based on pre-defined scenarios. This article describes how to create a Monitor Group on a decoder VJD 7xxx/ 8xxx in BVMS Configuration Client

DIVAR network 5000 / DIVAR hybrid 5000   support configuration of 3rd party cameras through the ONVIF Profile S protocol.

Follow the steps from this article if you want to configure your camera to detect motion and then send the event to the server, to start recording. This guide helps you set this option only for nights and weekends. It is important that you find the best possible motion detection settings for the camera in order to avoid unnecessary recordings or notifications.

Have a look at this article and learn what you should check when your cameras do not record and when going to VSG and recording, it stands that 'ANR not configured' or 'No more blocks available'

Follow this article if you have FLEXIDOME IP outdoor 5000i (FW 6.43.0027) or FLEXIDOME starlight 6000 VR (FW 6.32.0109) cameras and you would like to upgrade them to the latest version available

Can a stream of a Bosch camera be integrated into the end-user web page via http(s)?   Yes! You can use stream from our Bosch cameras to be displayed in a web page. Bosch IP cameras have a web server embedded and what you see when connecting to a camera with a web browser is a web page.

You can call desired pre-positions (PTZ) of Bosch IP cameras by using OSRD protocol or BiCom protocol. Please check this aticle to find some examples and detailed explanation.

This article contains the RCP+ commands (VJD 7513) to change the layout and see what camera you want to be displayed

The BVMS 11.1.1 Configuration Manual contains the lists for all components of BVMS, the ports that must be open within a LAN. You can find the used ports list starting with page 346 from the BVMS Configuration Manual.

First recommendation would be to configure the mode for IVA as a trigger, setting IVA as Profile 1 for “trigger off” and IVA as silent for “trigger on”.