Security: Video

AI Alarm Verification is applicable to Bosch Remote Portal cameras and 3rd party cameras**, for sites in Alarm Management which support alarm clip upload. 

This guide is meant to explain how to enable the appropriate debug commands for logging during random reboot situations, and which logging to collect for troubleshooting, as in general there are multiple triggers that can cause a device to reboot. The information gathered will help to analyze the root cause.  Please make sure that all of the logs collected cover the same time period.

This article explains how to set an Unconfigured Bad Drive to Unconfigured Good on a DIVAR IP 6000/ 7000. This step is required if the new drive is not listed under Unconfigured Drives. A possible reason for the Unconfigured Bad status is when a device that has not been removed properly is reconnected to the controller.

Video Recording Manger v4.00.0070 does not allow anyone not configured in VRM, only as an admin (using Configuration Manager), to log into the VRM Monitor page.

What happens when you upgrade the SW of your Management Server form e.g. BVMS 10.0 to BVMS 10.1 and you have not prepared a BVMS 10.1 activation key beforehand?

The default Community Strings for Bosch cameras is - public. To change it, please follow the steps below.

This article lists different ways to connect to cameras Live/Playback using the Video Security Client/App: to DIVAR IP AIO/BVMS system or to Camera directly, bypassing DIVAR IP AIO/BVMS system.  

When accessing the Operator Client from the Kiosk mode, the camera streams displayed on the cameos show a view that does not match the view from Operator Client running from desktop (Under the BVRAdmin account) or Remote Desktop.

This article contains videos which explain the usage of Bosch cameras integrated in Genetec Security Center.

This article describes the easiest method for adding Expansion shelves to a Base unit DSA E-Series E2600, E2700 or E2800.   This article also applies when: The amount of storage is overloaded and you need additional storage after fully populating the base shelf.   Article requirements: 1. Configuration Manager 2. Configuration Client which is included with BVMS 3. Santricity Software   Step-by-step guide      

The System Info File is requested during the BVMS license activation via Remote Portal and can be downloaded by following the steps described in this article

The firewall configuration dialog is a fixed step in the setup process and will allow automatic configuration of all required firewall settings to run BVMS.

The attached document provides more insights into the system configuration regarding the BVMS - Operator collaboration with Slack

According to its Data Sheet, the Flexidome IP 3000i IR camera has 2 options to activate the alarm input. Please refer to the diagram from this article if you would like to get alarm input from some physical sensors.

This article presents possible causes and solution regarding no recording for cameras added to VRM (DIP 7000AIO): ‘Unexpected error’ in BVMS Config Client

In this article you will see how to import project files into Configuration Manager in both versions: v6.10 & v7.41  

Let’s suppose that you have one setup which consists in an Adam 6060 I/O module, BVMS and a DINION IP thermal 8000 camera. Can the state of an ADAM relay module be changed when the IVA from the camera generates an alarm?

This article explains how to find the source (details of the workstation) and credentials that are used to attempt to login into BVMS (when the attempt has failed)

Network switch has port security on and shuts down a NetApp iSCSI data port (e.g. CH3). This article is only relevant in aspects of network security / port security where MAC addresses are analysed. Some network security applications are capable of sniffing network packets thoroughly enough to pick up MAC addresses on E-Series Controller ports that are not seen in the Storage Array Profile data.

Please keep in mind that for SNMP v3 only the the Standard MIB II file is supported. This means that only general network device performance monitoring parameters can be requested. There is no Bosch Private MIB II extension for SNMP v3.