According to its Data Sheet, the Flexidome IP 3000i IR camera has 2 options to activate the alarm input.
Please refer to the diagram from this article if you would like to get alarm input from some physical sensors.
With BVMS 11.0, new licensing system was introduced.
Attached document describes how to migrate existing activated BVMS licenses from the Bosch Software License Manager System (SLMS) licensing system to the new Bosch Remote Portal licensing.
Starting with BVMS 11.0, the standard BVMS licensing scheme also applies to the DIVAR IP units.
Attached document describes how the upgrade process to BVMS 11.0 looks like and what kind of licenses are needed for a DIVAR IP unit!
Do you have any doubts, regarding BVMS licensing?
Attached whitepaper might serve as comprehensive source of knowledge for BVMS licensing topics, like:
BVMS product editions and license types
License activation process
Assurance PRO ordering process
Managing your licenses in Remote Portal
and much more!
The camera supports the SNMP V1 (Simple Network Management Protocol) for managing and monitoring network components, and can send SNMP messages (traps) to IP addresses. It supports SNMP MIB II in the unified code.
You may need the SNMP MIB file when you are trying to monitor the camera through a Bosch or 3rd party software. This article aims to describe how to find and enable the SNMP on a DINION 6000 HD camera.
Same LAN connection between the camera and PC
A password prevents unauthorized access to the device. You can use different authorization levels to limit access. Proper password protection is only guaranteed when all higher authorization levels are also protected with a password. Therefore, you must always start from the highest authorization level when assigning passwords.
This article will guide you step by step to set the destination password for decoders.
There are two methods of working with 3 rd party apps: through Remote Portal and Configuration Manager.
The methods using the Configuration Manager can be used both with an online system (cameras connected to the internet) and an offline system (no internet connection to local system).
Once apps are installed on the camera, the configuration interface for each app can be accessed through the Local App Management Console on the camera. No internet connection required.
In this article you will find the step-by-step guide where is described the method using Configuration Manager.
The purpose of this article is to help you disabling the compass character from the Screen Display (OSD) of the PTZ camera via its web interface .
This example was troubleshooted on one AUTODOME dynamic 7000 HD camera with FW version 7.10.0076
This article provides a step-by-step guide about how you can disable UPnP of Bosch IP cameras & multicast scan from Configuration Manager.
One of the reason why UPnP (Universal Plug and Play) is enabled in our devices is because ONVIF uses this to scan the ONVIF device in the network.
In some cases the IVA tasks can get lost after firmware update.
There are 2 ways. In both ways it's not guaranteed that all task shall work afterwards since new firmware version can contain a new IVA version with new features. So please double check afterwards. It shall at-least save some time instead of starting from scratch.
NetApp SANtricity Dynamic Disk Pools (DDP) technology represents a significant advancement in storage system, data protection and data management. As disk capacities continue to grow without sufficient increases in data transfer rates, traditional RAID rebuild times are getting longer, even up to several days. This slow rebuild results in much more time with degraded performance and exposure to additional disk failures.
Logs are definitely important. We would even say they are the most important thing for a system to function properly.
At some point, the Central Support Team may ask you to provide them with the log files of your system.
The steps below can be used for the following models:
DIVAR AN 3000/5000 ,
DIVAR Hybrid 3000/5000,
DIVAR Network 2000/3000/5000
You can collect Service logs from the unit using two methods. Both methods will save the service logs as a password protected ZIP file ( Example: ServiceLog-20141204T172254.zip ).
Method 1 : from Local User Interface
Method 2 : remote, using a browser