Security: Video

This article presents what should be checked when the Sever State is Disconnected in Logical Tree from BVMS Operator Client.

This article shows what shoud be checked if the KBD-Digital cannot be connected to the BVMS workstation.

The “inactivity” algorithm from this article will move the camera to Pre-position 99 in the Alarm Task scripting.

This behavior was improved with the release of Video Security Client/App 3.2.3.

RAID 5 provides basic fault tolerance with good performance, but it cannot protect against multiple drive failures. RAID 5 with a hot spare improves fault tolerance by automatically replacing failed drives, but it still has the same limitation regarding multiple drive failures. RAID 6 offers a higher level of fault tolerance by using double parity, allowing for the simultaneous failure of up to two drives without data loss. However, it has higher write overhead and requires more drives for implementation compared to RAID 5.

NetApp SANtricity Dynamic Disk Pools (DDP) technology represents a significant advancement in storage system, data protection and data management. As disk capacities continue to grow without sufficient increases in data transfer rates, traditional RAID rebuild times are getting longer, even up to several days. This slow rebuild results in much more time with degraded performance and exposure to additional disk failures.

One of the possible traps  that DIVAR IP hybrid/network can send is HDD_STATUS_CHANGE. The HDD_STATUS_CHANGE is triggered when the status of the Hard Disk changes. 

The URL for RTSP stream (for example in VLC Media Player) should have the format as described in this article

If you want to improve the image quality of your Bosch camera and you did not find the FPS option in the Web User Interface, please follow this article and you will find the answer.

If you were asked by the Central Technical Support team to provide them with the Bios defaults picture with the Boot order of your DIVAR IP during the troubleshooting process of your device, please follow the steps from this article and find out how can you check the boot order of a DIVAR IP

To access the "Reset" options of a DIVAR IP 2000 Recording Appliance, you have to open the Appliance's "Dashboard".

🛈 Port Forwarding Allows remote computers (for example, computers on the Internet) to connect to a specific computer or service within a private local-area network (LAN). In a typical residential network, nodes obtain Internet access through a DSL or cable modem connected to a router or network address translator (NAT/NAPT). Hosts on the private network are connected to an Ethernet switch or communicate via a wireless LAN. The NAT device's external interface is configured with a public IP address. The computers behind the router, on the other hand, are invisible to hosts on the Internet as they each communicate only with a private IP address. When configuring port forwarding, the network administrator sets aside one port number on the gateway for the exclusive use of communicating with a service in the private network, located on a specific host. External hosts must know this port number and the address of the gateway to communicate with the network-internal service. Often, the port numbers of well-known Internet services, such as port number 80 for web services (HTTP), are used in port forwarding, so that common Internet services may be implemented on hosts within private networks.

This article aims to provide concerned parties, such as customers, users, operators or consultants, with an overview of data privacy and protection related features of BVMS Person Identification. Moreover, this article describes how data, as processed during the Person Identification steps, can be classified. Finally, this article lists technical measures for data protection in the context of BVMS Person Identification.

This article explains how to find the source (details of the workstation) and credentials that are used to attempt to login into BVMS (when the attempt has failed)

This article explains the meaning of the arrows in circle at the central logical tree in the BVMS Operator Client list

The validity of the SMA date should cover the BVMS version release date you wish to upgrade to. Otherwise, the upgrade will not work and you will get the message "It is not possible to upgrade the software of this System Info file to a newer version". Also, please note that this message could occur in case you are trying to upgrade your BVMS and it is on the latest available version released.

Using the following command you can reset the result of People counting via SDK: http://<IP_address>/rcp.xml?command=0x0b4a&type=P_OCTET&direction=WRITE&num=1

According to the release note of the Video Security Client (page 3), you will notice that it is specified that the export of the mp4 video using the Video Security App on iOS or Android device is not possible, while for PC should work without issues.

Find out from this article what you should check when there is a black image of your camera in Operator Client when clicking on the Instant Playback

“Server is not online” message is displayed when accessing BVMS Operator Client. After clicking OK, the Operator Client is opening in a loop and never stops. What should you do?